Table of Contents
Advertisement
■
Operation section
Push each button to select a desired operation.
• The control saves commands in memory and after the initial setting, there is no need for any additional settings
unless changes are desired. The air conditioner can be operated by pushing the
1
2
3
4
1
button (Temperature set button)
Adjusts the set point.
Select the desired set point by pushing TEMP.
or TEMP.
.
2
button (Timer set button)
Use to setup the timer.
3
button (Filter reset button)
Resets " " display after cleaning filter.
4
button (Test button)
Use only for service.
(During normal operation, do not use this
button.)
5
button
When the button is pushed, the operation starts,
and it stops by pushing the button again.
When the operation has stopped, the operation
lamp and all the displays disappear.
6
Operation lamp
Green light illuminates when unit is on.
Although it flashes when operating the
protection device or a problem occurs.
7
button (Operation mode button)
Selects desired operation mode.
8
button (Fan speed button)
Fan speed is not adjustable.
9
button (Ventilation button)
Use when a power ventilation kit (locally
procured) is connected.
• If "
" is displayed on the remote controller
when this button is pushed, no vent kit
connected.
15-EN
button.
5
6
7
8
9
10
11
12
10
button (Power save operation)
Use to initiate power saving mode.
11
button (Unit / Louver select button)
Selects a unit number (left) and louver number
(right).
UNIT:
Selects an indoor unit when multiple indoor units
are controlled with one remote controller.
LOUVER:
No Function.
12
button (Swing / Louver direction
button)
No Function.
OPTION:
Remote controller sensor
Usually the temperature sensor of the indoor unit
senses the temperature. The temperature on the
surrounding of the remote controller can also be
sensed.
For details, contact the dealer from which you have
purchased the air conditioner.
4
Correct usage
When the air conditioner is used for the first time or when the setting is changed, follow the steps below.
Settings are saved in memory and are displayed anytime the unit is turned on by pushing the
■
Preparation
• When the circuit breaker is turned on, the partition lines are displayed on the remote controller.
* After the circuit breaker is turned on, the remote controller does not accept any commands for approx.
1 minute, this is not a failure.
REQUIREMENT
When the air conditioner is re-powered after it has not been used for a long period, turn on the circuit breaker at
least 12 hours before starting the air conditioner.
TEMP.
ON / OFF
4
TIMER SET
FAN
MODE
TIME
SAVE
VENT
FILTER
RESET
TEST
SET
CL
SWING/FIX
UNIT LOUVER
Start
1
Push
button.
The operation lamp illuminates, and the operation
starts.
2
Select an operation mode with the "
button.
One push of the button, and the display changes
in the order shown below.
Auto
Heat
Dry
Cool
Fan
– 8 –
3
Select fan speed with "
One push of the button, and the display changes
in the order shown below.
Auto
High
1
• When fan is in "
Auto", fan speed is
3
2
adjusted based on difference between set
point and room temperature.
• In heating operation, if the room temperature
is not heated sufficiently with speed "
operation, select "
Med." or "
operation.
• The temperature sensor detects the return air
temperature at the indoor unit, which differs
from the room temperature depending on the
installation condition.
Set point is a target of room temperature.
(
"Auto" is not selectable in the Fan
"
mode.)
4
Select the set point temperature by pushing
the "TEMP.
" or "TEMP.
Stop
Push
button.
The operation lamp goes off, and the operation stops.
button.
" button.
Med
Low
Low"
High"
" buttons.
16-EN
Advertisement
Table of Contents
