Summary of Contents for Pace SODRTEK ST 600
- Page 1 Operation and Maintenance Manual for the ® SODRTEK ST 600 Digital Paste Dispensing System P/N 5050-0538...
-
Page 2: Table Of Contents
Helpful Hints for Proper Dispensing................9 Tip Selection .........................10 Corrective Maintenance ....................10 Packing List........................11 Spare Parts and Accessories..................12 Service ..........................13 “SODRTEK by PACE” LIMITED WARRANTY STATEMENT........14 Contact Information.......................15 ©2004 PACE Inc., Annapolis Junction, Maryland Page 2 of 15 All Rights Reserved... -
Page 3: General Information
General Information Introduction ® Thank you for purchasing the PACE SODRTEK model ST 600 Digital Paste Dispensing System. This manual will provide you with the information necessary to properly set up, operate and maintain your new system. This ST 600 is a microprocessor controlled, automatic liquid dispensing system. -
Page 4: Parts Identification
Finger Switch Receptacle Dispensing Time Indicators/Buttons Dispensing Output Pressure Fitting Air Pressure Gauge AC Power Receptacle/Fuse Holder Foot Pedal Receptacle Dispensing Mode DIP Switches Air Input Fitting ©2004 PACE Inc., Annapolis Junction, Maryland Page 4 of 15 All Rights Reserved... -
Page 5: Safety
2. To prevent personnel injury, adhere to safety guidelines in accordance with OSHA and other applicable safety standards. 3. Always use PACE systems in a well ventilated area. A fume extraction system such as those available from PACE are highly recommended to help protect personnel from solder flux fumes. -
Page 6: System Set-Up
Dispenser Cubby. 10. Insure that the foot pedal is connected to the FOOT PEDAL Receptacle on the rear panel. Material Loading PACE recommends the use of preloaded barrels whenever practical to minimize any handling or safety precaution requirements. When loading is required, adhere to all precautions recommended by the material manufacturer. -
Page 7: Operation
7. Insure that the proper material (in barrel) and tip have been installed. 8. Wipe any material residue from the end of tip. ©2004 PACE Inc., Annapolis Junction, Maryland Page 7 of 15 All Rights Reserved... -
Page 8: Adjustment Of Dispensing Modes
Be triggered once, dispense at controlled time ten times. Be triggered once, dispense at controlled time eleven times. Be triggered once, dispense at controlled time twelve times. ©2004 PACE Inc., Annapolis Junction, Maryland Page 8 of 15 All Rights Reserved... -
Page 9: Helpful Hints For Proper Dispensing
Helpful Hints for Proper Dispensing PACE recommends that the operator become familiar with the operation of the dispenser by first applying the material to a piece of paper or scrap PC board. Use this method to obtain the desired results for each dispensing material and application. -
Page 10: Tip Selection
Clean or replace solenoid as necessary. Blowing fuse Incorrect rated fuse Verify the rating of the fuse. Internal short Unplug power input, remove cover, and check internal wiring for loose connection. ©2004 PACE Inc., Annapolis Junction, Maryland Page 10 of 15 All Rights Reserved... -
Page 11: Packing List
Power cable (Export) Foot Pedal Barrel rack Air-input tube (3m) 10cc Barrel Adapter Finger Switch Assembly 6008-0143-P1 Fuse (120V, 0.25A) Fuse (230V, 0.5A) Operations Manual CD CD5050-0459 ©2004 PACE Inc., Annapolis Junction, Maryland Page 11 of 15 All Rights Reserved... -
Page 12: Spare Parts And Accessories
Threaded hub, 20GA, 0.1" 1125-0041-P50 Threaded hub, 21GA, 0.1" 1125-0022-P10 Threaded hub, 21GA, 0.1" 1125-0022-P50 Threaded hub, 22GA, 0.1" 1125-0023-P10 Threaded hub, 22GA, 0.1" 1125-0023-P50 Threaded hub, 23GA, 0.1" 1125-0024-P10 ©2004 PACE Inc., Annapolis Junction, Maryland Page 12 of 15 All Rights Reserved... -
Page 13: Service
Barrel/Stopper, 10cc, 40 bag 1125-0039-P5 Barrel/Stopper, 30cc, 40 bag 1125-0040-P1 Barrel/Stopper, 30cc, 40 bag 1125-0040-P5 Service Please contact PACE or your local distributor for service and repair. ©2004 PACE Inc., Annapolis Junction, Maryland Page 13 of 15 All Rights Reserved... -
Page 14: Sodrtek By Pace" Limited Warranty Statement
Warranty service may be obtained by contacting the appropriate PACE Company or local Authorized PACE distributor as set forth below to determine if return of any item is required, or if repairs can be made by the user in the field. Any warranty or other claim with respect to the products must be made with sufficient evidence of purchase and date of receipt, otherwise user’s rights under this warranty shall be... -
Page 15: Contact Information
PACE Incorporated retains the right to make changes to specifications contained herein at any time, without notice. Contact your local authorized PACE Distributor or PACE Incorporated to obtain the latest specifications. The following are trademarks and/or service marks of PACE, Incorporated, MD, USA: ™...