Invision HDTV-DXL Instruction Manual

www.InvisionTechnology.co.uk
Parts List:
First things first: Check the box contains all the items in the parts list above.
Check VESA Compatibility: Please check the VESA measurements before drilling any holes (to check your
TVs VESA, measure the distance between the mounting holes on the back of the TV).
Check the weight of your TV: You may need an extra person on hand to help.
Please wear safety glasses before using your drill – if in any doubt, consult your retailer or an experienced
installer.
Y ou will need a few additional tools: A drill and 10mm masonry drill bit or 4mm wood drill bit (depending on the
fixing surface), a large Phillips screwdriver a pencil and a spirit level. You may choose to use a ratchet and
10/12mm socket but a 10/12 mm socket with Allen key is provided.
Now please read the instructions fully and plan how to mount your TV bracket.
Severe personal injury and property damage can result from improper installation or assembly. Please read the following warning carefully before beginning.
• Product must be installed by a professional or competent installer.
• If you do not understand the instructions or have any concerns or questions please contact us or a competent installer.
• Do not install or assemble if the product or hardware is damaged or missing. If you require replacement parts, please contact us at Invision for assistance.
• This product fits most 37"-70" LCD/LED/plasma screen, maximum weight of LCD/LED/plasma screen 50kg (110lb).
• This product has been designed for use on vertical walls constructed of wood studs (minimum 2" x 4"/ 51mm x 102mm) or masonry (solid concrete 2000 PSI density minimum).
• For safe installation, the wall you are mounting must support minimum 3 times the weight of the total load (the TV bracket, the TV and all accessories).
• Do not use this product for any other application than the original design purpose.
• This product contains moving parts, please use with caution.
• When installing flat panel display, take care not to damage electrical wiring or power source.
• The manufacturer will bear no responsibility for mounting to the vertical wall, or incidental or consequential damages arising there from.
• The manufacturer disclaims any liability for the modifications, improper installation or installation over the specified weight range.
• The manufacturer will not be liable for any damages arising from the use of, or inability to use the product.
Lets Get Started!
If you require assistance please contact us at: help@InvisionTechnology.co.uk
English
Invision HDTV-DXL
Double Arm TV Wall Mount
Instruction Manual
VESA Compliance 200(w)x100mm(h) - 600(w)x400mm(h)
Recommended Screen Sizes 37" - 75"
Integrated Cable Management
Load Capacity 50kg (110lbs)
To receive large format PDF instructions please
email help@InvisionTechnology.co.uk
Tools List:
WARNING!
1
Step 1 Unboxing
1. Lay the bracket flat and extend the bracket arms by holding the wall plate and pulling upwards on mounting
plate.
2. Remove the 2x wall plate covers and put to one side - see diagram 'A'. Now remove 2x securing bolts using
a screwdriver or Socket and Allen key 'F' and also put to one side (both wall plate covers and securing bolts will
be used later on step 4).
3. Remove the mounting plate and put the rest of the bracket assembly to one side.
Diagram 'A'
Step 2a Assembling and Securing Mounting plate to TV
1. Slide both the longest rails '1.' through the mounting
plate and secure with bolts 'E'.
2. Align the 2x shortest rails '2.' vertically so the notches
engage with the horizontal rail '1'.
3. Slide to exact width of TV VESA measurements e.g.
400mm (w) x 200mm (h). Insert nuts and bolts 'C/D' and
tighten assembly - see diagram 'B'.
Diagram 'C'
Spacers and washers can be used in front or
behind TV mounting assembly. Use bolts (G - O)
to secure mounting assembly to TV.
v20220526
Mounting plate
Securing bolts
Wall plate
Wall plate covers
Step 2b
1. Lay TV face down onto a flat surface to access TV fixing points
and position TV mounting assembly onto back of TV - see diagram
'C'.
2. Use relevant bolts, washers and spacers to secure the vertical
rails of the TV mounting assembly to the back of your TV. (Spacers
and washers can be used when shorter fixing bolts are required,
clearance for cable access or if the rear of the TV is not flat).
2
Diagram 'B'