Invision MX250 Instruction Manual

www.InvisionTechnology.co.uk
Parts List:
(C/G can be used as
a socket wrench)
First things first: Check the box contains all the items in the parts list above.
Check VESA Compatibility: Please check the VESA measurements before drilling any holes (to check your
TV/Monitor VESA, measure distance between mounting holes on back of the TV/Monitor).
Check the weight of your TV/Monitor: You may need an extra person on hand to help!
Y
ou will need a few additional tools: A drill and 10mm masonry drill bit or 4mm wood drill bit, depending on
the fixing surface, a large Phillips screwdriver, a pencil, a spirit level and a 12mm socket and ratchet
(a 12mm socket can be used with the Allen key which are supplied – Parts C & G).
Please wear safety glasses before using your drill – if in any doubt, consult your retailer or an experienced
installer.
NB NG P E E N TE: N T
This product is packed with the faceplate at a 45° angle to fit smaller packaging and reduce environmental waste.
Please rotate the faceplate 45° clockwise before mounting your monitor.
P E E N TE: c pl o on h h gh nc by
no l n n h yo c n ll b h l y fo
ov n
Now please read the instructions fully and plan how to install your wall mount!
Severe personal injury and property damage can result from improper installation or assembly. Please read the following warning carefully before beginning.
• If you do not understand the instructions or have any concerns or questions please contact us or a competent installer.
• Do not install or assemble if the product or hardware is damaged or missing. If you require replacement parts, please contact us at Invision for assistance.
• This product fits most VESA compliant 17"-27" TV/monitors to a maximum weight of 7kg (15.4lb).
• This product has been designed for use on a vertical wall construction (minimum 2" x 4"/ 51mm x 102mm) or masonry (solid concrete 2000 PSI density minimum).
• Do not use this product for other than the original design purpose.
• This product contains moving parts, please use with caution.
• When installing TV/monitor take care not to damage electrical wiring or power source.
• Important - mains and data cables must be free from twisting and/or shearing.
• The manufacturer disclaims any liability for the modifications, improper installation or installation over the specified weight range. The manufacturer will not be liable for any damages arising from the use of, or inability to use the product.
• This product is designed for indoor use only, use of this product outdoors could lead to product failure and severe personal injury.
• This product contains a high pressure gas spring. This mechanism is not user serviceable and any interference could result in injury or damage. Please dispose of with caution.
• In order to ensure the performance of the gas spring it is recommended to fully extend the arm several times per month.
Lets Get Started!
If you require assistance please contact us at: help@InvisionTechnology.co.uk
English
Invision MX250
Ergonomic Gas Assisted TV/Monitor
Wall Mount
Instruction Manual
VESA Compliance 75x75mm & 100x100mm
Recommended Screen Sizes 17" - 27"
Integrated Cable Management
Load Capacity 2 - 7kg (4.4 - 15.4lbs)
To receive large format PDF instructions please email
help@InvisionTechnology.co.uk
Tools List:
T B EN
gn n y n l l fo c o ov Th
ny y o co ho ny n n
WARNING
1
Step 1 - Preparing your Wall Mount
1. Open the box and take out the wall mount. Remove 2x wall plate cover caps as shown in Diagram 'A' and
put them to one side. (Important: Do NOT attempt to adjust the tension of the wall mount before
mounting it on the wall).
Tip: use one of the fixing
screws and push through
the hole on the back of the
wall plate to release the cap
Step 2 - Positioning and Marking Out
1. Before marking out note the centre line of the face plate will be offset to the wall fixing plate when the wall
mount is folded back to the wall (the amount of offset varies when the screen is raised or lowered) - see
diagram 'B'.
This wall mount is also height adjustable so take into consideration the length of cables you are using
with your equipment leaving an adequate amount of slack so the wall mount can function properly.
2. Position the mount on the wall using the wall fixing plate as a template and mark using a spirit level and
pencil. (Ensure your markings are level both horizontally and vertically on the wall) - see diagram 'C'.
Step 3 - Securing Wall Mount to your Wall
This wall mount is designed to be attached to either fixed wooden studs within traditional plasterboard (drywall)
walls or into solid brick or concrete walls.
45
Step 3a - Wood Stud Installation
1. For mounting to wooden studs – carefully locate the wooden stud and mark the position of the holes level
vertically and drill into the wood using a 4mm drill to a depth of 80mm - see diagram 'D'.
2. Hold your wall mount in position and insert the supplied screws and washers, check the wall mount is level
and fully tighten into the wood using a 12mm socket and ratchet or parts 'C/G' socket wrench (plastic plugs are
not required when fixing into wood) - see diagram 'E'. Replace wall plate cover caps once the wall mount is
secure.
Diagram 'D'
v20221025
Diagram 'A'
Diagram 'B'
Maximum
height
Face
Height
Plate
adjustability
Minimum
height
Wall fixing
plate
Diagram 'E'
2
Diagram 'C'