Summary of Contents for Brunswick CANTON SHUFFLEBOARD
Page 1
ASSEMBLY INSTRUCTION MANUAL CANTON SHUFFLEBOARD www.brunswickbilliards.com SERVICE DEPARTMENT, P.O. BOX 68, BRISTOL, WI 53104 EMAIL: BRUNSWICKSERVICE@BRUNSWICKBILLIARDS.COM Page 1 May 2018 51-906359-000...
Page 2
CANTON SHUFFLEBOARD CABINET HALF(2) LEG POST ASSY(6) PLAY FIELD(1) SHORT END STRETCHER(2) RH STRETCHER BAR(2) LH STRETCHER BAR(2) STRETCHER TURNBUCKLE(1) SHORT CENTER STRETCHER(1) HEX HEAD BOLT WEIGHTS-RED(4)BLACK(4) SHUFFLEBOARD WAX(1) BOARD SWEEP(1) 7/8-9UNC X 1 1/2(2) Page 2 May 2018 51-906359-000...
PACKAGE CONTENTS CONTINUED CANTON SHUFFLEBOARD CUSTOM WASHER CUSTOM WASHER HEX BOLT, 3/8-16UNC X 2 1/4(24) HEX BOLT, 3/8-16UNC X 1 3/4(6) .78 ID X 2.5 OD(2) 1.06 ID X 2.5 OD(4) FLAT WASHER, 3/8(32) SPRING LOCK WASHER,3/8(32) WOOD DOWEL, 3/8 X 1(8)
Page 4
CANTON SHUFFLEBOARD LEG & SHORT STRETCHER ASSEMBLY(END & CENTER): Step 1: Assemble (2)legs and (1)short end stretcher using (2)3/8-16 x 1 3/4 hex head bolt, (2) 3/8 flat washer, and (2)3/8 split lock washer as shown in FIGURE 1.(END ASSEMBLY) Step 2: Repeat Step 1 for second assembly.(END ASSEMBLY)
CANTON SHUFFLEBOARD CABINET ASSEMBLY: Step 1: Place each cabinet half upside down inline near the final unit location. (Use protective material, such as shipping blankets, between cabinet and floor) Step 2: Insert wood dowels into dowel holes on one cabinet half and slide the cabinet halves together. (See Figure 3)
Page 6
CANTON SHUFFLEBOARD CABINET ASSEMBLY CONTINUED: Step 1: Place the previously assembled center leg/stretcher assembly into the cavity at the center, where the two cabinet halves come together. Securely attach the assembly in place using (8)3/8 flat washers, (8)3/8 spring lock washers, and (8)3/8-16 x 2 1/4 hex bolts.
Page 7
CANTON SHUFFLEBOARD CABINET ASSEMBLY CONTINUED: Step 1: Carefully insert the stretcher bar assembly end with cross threaded hole into the center short stretcher. At the same time positioning the opposite end of the stretcher bar assembly in-line with the mating hole in the end stretcher.
Page 8
CANTON SHUFFLEBOARD CABINET PLACEMENT & LEVELING: Step 1: Using two people, carefully roll cabinet into an upright postion and place in the final unit location. Step 2: Using a bubble level, place wood shims(NOT INCLUDED) under legs as needed, level the cabinet across width and along the entire length.
Page 9
CANTON SHUFFLEBOARD PLAY FIELD PLACEMENT & ADJUSTMENT: Step 1: Place play field into the cabinet. For best results use weights, two on each end, to rest the play field on and prevent injury. Lift each end from under the cabinet, one end at a time, and remove the weights. Center the play field within the cabinet equally along length and across width.(See Figure 8) Step 2.
CANTON SHUFFLEBOARD BASIC RULES OF PLAY: 1. Object of the game is to score more points than your opponent by either knocking their weights off the play surface or by sliding your weights into a higher scoring zone. A typical game, singles or partners, is played to 15 points.
Need help?
Do you have a question about the CANTON SHUFFLEBOARD and is the answer not in the manual?
Questions and answers