Related Manuals for Brunswick Metro
Summary of Contents for Brunswick Metro
- Page 1 Metro POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 SEPTEMBER 2005 51-905486-001...
- Page 2 NOTE: Please use the instructions in this manual to assemble the tables shown below. Illustrations may be different depending on the table being assembled. Also note that careful handling of all components will assure damage-free assembly. PAGE 2 BRUNSWICK INSTALLATION MANUAL...
- Page 3 16-18 x 1-1/4” hex head bolts and 5/16 flat washers. Step #7: Loosely attach the baseframe to the brackets using 3/8-16 x 2-3/4” hex head bolts, 3/8 flat washers and 3/8-16 hex nuts. FIGURE THREE BRUNSWICK INSTALLATION MANUAL PAGE 3...
- Page 4 The levelers should be rotated out atleast 1/4” to allow for further leveling when the slate is attached. NOTE: Try to leave atleast 5’ between the outer edge of the baseframe to any wall. FIGURE SIX PAGE 4 BRUNSWICK INSTALLATION MANUAL...
- Page 5 Step #9: Slate joints can now be filled with Rock Hard FIGURE TWO putty or wax. Lightly sand or scrape across the joints after grouting. BRUNSWICK INSTALLATION MANUAL PAGE 5...
- Page 6 This is important as this will provide cushioning from ball impact and the bed cloth will last much longer. Step #11: Clean top of slate thoroughly with a damp cloth before applying the bed cloth. FIGURE THREE PAGE 6 BRUNSWICK INSTALLATION MANUAL...
- Page 7 Step 1. Step #6: Stretch the cloth from #1 to #3 and press into position. Step #7: Stretch the cloth #3 to #4, pulling from #1 and #2. Press into place. FIGURE THREE BRUNSWICK INSTALLATION MANUAL PAGE 7...
- Page 8 #5 and toward the side pocket from #2 and tack or staple at #7. Step #10: Repeat Step 7, stretching from #6 and toward the side pocket from #4 and tack or staple at #8. FIGURE THREE PAGE 8 BRUNSWICK INSTALLATION MANUAL...
- Page 9 NOTE: Occasionally cloth will stretch, leaving wrinkles at the pockets. To retighten, remove apron, one end rail and one side rail. Pull cloth taut, and retack or restaple FIGURE SEVEN along the open end and side to restore original tightness. BRUNSWICK INSTALLATION MANUAL PAGE 9...
- Page 10 Step #6: Turn rail over and at corner pockets fold the cloth over the mitred edge as shown, stretching tightly and working out any wrinkles as you staple three places in area shown. FIGURE FIVE PAGE 10 BRUNSWICK INSTALLATION MANUAL...
- Page 11 Step #12: Hold the small fold in place with thumb and forefinger and firmly hold it down over facing. Then staple at rear of facing and at bottom of rail as shown. Step #13: Trim excess cloth as required. FIGURE TEN BRUNSWICK INSTALLATION MANUAL PAGE 11...
- Page 12 5/16-18 weld nuts. Tighten finger tight, square the rail assembly and tighten all casings securely. NOTE : the castings will not be flush with the top and back of the rails you will have about a 1/8” overhang. FIGURE THREE FIGURE FOUR PAGE 12 BRUNSWICK INSTALLATION MANUAL...
- Page 13 Attach with #10 x 1/2” pan head tapping screws. Step #5: Properly position the aprons to the rail and secure all apron hardware. FIGURE FIVE FIGURE SIX BRUNSWICK INSTALLATION MANUAL PAGE 13...
- Page 14 5/8” socket head machine screws and #10 external tooth washers. FIGURE EIGHT FIGURE NINE Step #11: Thoroughly brush the area on which the bed Step #12: Locate and install bed spots for each type of table as shown. FIGURE NINE PAGE 14 BRUNSWICK INSTALLATION MANUAL...
- Page 15 Install the foot end tracks first then butt the head track to the foot track. NOTE: To obtain a smoother roll the wires can be bent to match. FIGURE THREE BRUNSWICK INSTALLATION MANUAL PAGE 15...
Need help?
Do you have a question about the Metro and is the answer not in the manual?
Questions and answers