Subscribe to Our Youtube Channel
Related Manuals for Brunswick Pursuit
Summary of Contents for Brunswick Pursuit
- Page 1 Pursuit™ POCKET BILLIARD TABLE INSTALLATION MANUAL www.brunswickbilliards.com SERVICE DEPARTMENT P.O. BOX 68 BRISTOL, WI 53104 EMAIL: BRUNSWICKSERVICE@BRUNSWICKBILLIARDS.COM August 2020 51-906473-001...
- Page 2 PARSONS NOTE: Please use the instructions in this manual to assemble the table shown. Also note that careful handling of all components will assure damage-free assembly. PAGE 2 BRUNSWICK INSTALLATION MAN UAL...
- Page 3 1/2-13 X 3-1/2 HEX BOLT leave connection slightly loose. LOCK WASHER FLAT WASHER FIGURE TWO FIGURE THREE Step #4: (Requires Two People) Flip assembly over so that it is right-side up as shown in Figure Three. FIGURE THREE BRUNSWICK INSTALLATION MANUAL PAGE 3...
- Page 4 Figure Five. FIGURE FIVE FIGURE SIX 3/8-16 NUT LOCK WASHER Step #7: Repeat Step 6 to connect the two remaining leg FLAT WASHER assemblies at the other end. FIGURE SIX PAGE 4 BRUNSWICK INSTALLATION MAN UAL...
- Page 5 Measure width and length from outer corners of the legs as well, it is critical that these measurements are equal end-to-end and side-to-side. Tighten the leg connection once legs are in position. FIGURE SEVEN BRUNSWICK INSTALLATION MAN UAL PAGE 5...
- Page 6 Step #8: With all three sections leveled, the slate joints can now be lled using rock hard putty or slate joint wax. Scrape excess material away leaving a smooth surface across each joint. FIGURE FOUR PAGE 6 BRUNSWICK INSTALLATION MAN UAL...
- Page 7 Step #4: Tack or staple the cloth securely to the wood frame at #1 with two tacks or staples approximately 2” apart. Step #5: Stretch the cloth across the table and tack or staple securely at #2 with two tacks or staples 2” apart. BRUNSWICK INSTALLATION MAN UAL PAGE 7...
- Page 8 Step #13: Stretching the cloth tightly across the table from location #9, repeat Steps 12 and 13 at location #10. FIGURE FIVE PAGE 8 BRUNSWICK INSTALLATION MAN UAL...
- Page 9 Step #23: Trim off excess cloth around the perimeter of the slate. Step #24: Locate the eighteen (18) rail attach holes HOOK & LOOP STRIP and cut clearance holes in the cloth with a sharp knife. POCKET LINER FIGURE EIGHT BRUNSWICK INSTALLATION MAN UAL PAGE 9...
- Page 10 #8 x 1/2 PAN SCREW Head Screws as shown in Figure One. Step #2: Repeat Step #1 for the second pocket leather LEATHER BUCKET bucket on the opposite side. #8 x 1/2 PAN SCREW FIGURE ONE PAGE 1 0 BRUNSWICK INSTALLATION MAN UAL...
- Page 11 Step #6: Turn rail over and at corner pockets fold the cloth over the mitred edge as shown, stretching tightly and working out any wrinkles as you staple three places in area shown. FIGURE FIVE BRUNSWICK INSTALLATION MANUAL PAGE 11...
- Page 12 Step #12: Hold the small fold in place with thumb and forenger and rmly hold it down over facing. Then staple at rear of facing and at bottom of rail as shown. Step #13: Trim excess cloth as required. FIGURE TEN PAGE 1 2 BRUNSWICK INSTALLATION MAN UAL...
-
Page 13: Rail Assembly
For best results, turn each Threaded Rod all the way 3/8-16UNC X 2-3/4 in until contact with wood is made, and then, back the THREADED ROD Threaded Rod out 1/4 turn. FIGURE TWO BRUNSWICK INSTALLATION MAN UAL PAGE 13... - Page 14 HEAD FOOT NOTE: Bed spots are self-adhesive. Bed spots can be applied at both head and foot end of the table, or just the foot end, whichever is preferred. FIGURE FIVE PAGE 1 4 BRUNSWICK INSTALLATION MAN UAL...
Need help?
Do you have a question about the Pursuit and is the answer not in the manual?
Questions and answers