Specification List; Model Name - Mitsubishi MELSERVO MR-J2S-A-PY091 Series Manual

1.3 Specification List

(1) Servo amplifiers
Servo Amplifier Model
MR-J2S-
V o l t a g e / f r e
q u e n c y
( N o t e 1 )
P e r m i s s i b l e
P o we r
v o l t a g e
s u p p l y
f l u c t u a t i o n
Permissible
frequency
fluctuation
C o n t r o l s y s t e m
P r o t e c t i v e
f u n c t i o n s
S t r u c t u r e
A m b i e n t
t e m p e r a t u r e
A m b i e n t
E n v i r o
h u m i d i t y
n m e n t
A m b i e n c e
A l t i t u d e
V i b r a t i o n
W e i g h t
( k g )
Note: 1. The rated output capacity and rated speed of a servo motor used with the servo amplifier assumes that the power supply
voltage and frequency are as indicated. They cannot be guaranteed when a power supply voltage drop occurs.
2. The torque characteristic of the servo amplifier used with a servo motor assumes that the voltage is three-phase 200 to
230VAC or single-phase 230VAC.

1.4 Model Name

A special number is added to the model name of the servo amplifier.
M R − J 2 S −
10A 20A 40A 60A
-PY091 -PY091 -PY091 -PY091
Three-phase 200 to 230VAC/50, 60Hz or
single-phase 230VAC/50, 60Hz (Note 2)
Three-phase 170 to 253VAC/50, 60Hz
or single-phase 207 to 253VAC/50, 60Hz
Overcurrent shutoff, regenerative overvoltage shutoff, overload shutoff (electronic thermal relay), servo
motor overheat protection, encoder error protection, regeneration error protection,
undervoltage/instantaneous power failure protection, overspeed protection, error excessive protection
Self-cooling, open (IP00)
0 to 55(C (non-freezing), storage: -20 to 65(C (non-freezing)
90%RH or less (non-condensing), storage: 90%RH or less (non-condensing)
Indoors (no direct sunlight), without corrosive gas, flammable gas, oil mist, dust and dirt
0.7 0.7 1.1 1.1
− P Y 0 9 1
A
70A 100A 200A 350A
-PY091 -PY091 -PY091 -PY091
Three-phase 200 to 230VAC/50, 60Hz
(Note 2)
Three-phase 170 to 253VAC/50, 60Hz
Within ±5%
Sine-wave PWM control/current control system
Forced cooling, open (IP00)
1000m or less above sea level
5.9m/s2 or less
1.7 1.7 2.0
Indicates that the servo amplifier software
conforms to this specification.
PY091: 0.05kW to 3.5kW type
S091: 5.0kW to 7.0kW type
-5-
500A 700A 10A1
-S091 -S091 -PY091
Single-phase 100 to
120VAC/50, 60Hz
Single-phase 85 to
127VAC/50, 60Hz
Self-cooling, open (IP00)
2.0 4.9 7.2 0.7
20A1 40A1
-PY091 -PY091
0.7 1.1
BCN-B32110-011