Eldat RT35-4104M-01, RT35-5004M-01 - Micro Transmitter Intended Use

Models

RT35-4104M-01
4 channel 433.92 MHz

RT35-5004M-01
4 channel 868.30 MHz

Intended Use

This transmitter may only be used to operate ELDAT radio controls.
The manufacturer shall not be liable for any damage caused by improper or nonintended use!

Technical Details

Coding: Factory coding with over 70 million options.
Range: approx. 200 m (under favourable free-field conditions)
Power supply: 1x 3 V battery, CR 2032
Indicator: LED
Degree of protection: IP 54
Operating temperature: - 20°C to +60°C
Dimensions: (WxHxD) 70 x 40 x 17 mm
Weight: 25 g (incl. battery)

Scope of Delivery

Transmitter incl. battery
Programming connector
Operating instructions

Preparing Transmitter

Transmit the transmitter code to the receiver (see operating instructions of the receiver / radio control).

Memorizing Codes

This function allows to transfer the codes of one transmitter to other hand transmitters.

1. Connect the source transmitter to the target transmitter using the programming connector.
   
   
2. Press and hold the selected channel button of the source transmitter. The LED in the source transmitter lights up.
3. Press and hold the respective channel button of the target transmitter. The LED in the target transmitter initially starts flashing and then lights up after approx. 2 sec.
4. Release the channel buttons and to remove the programming connector. The programming is completed.

Repeat steps 1 to 4 for programming each individual channel.

Changing Codes

This function allows the receiver to be re-coded in case a transmitter is lost.

1. Put the programming connector into the transmitter to be re-coded.
2. Short-circuit one of the two outer wires of the programming connector with the centre wire.
   
   
3. Press the respective channel button for approx. 5 seconds. The channel is coded anew (random programming).

4. Release the channel but ton of the transmitter and remove the programming connector. The re-coding is completed.

Repeat steps 1 to 4 for recoding each individual channel.
Note: The new coding must be transferred to the receiver (consult the operating in structions of the receiver / radio control).

Operating the Transmitter

Press and hold the button until the LED lights up. The transmitter has a battery check function, which checks the capacity of the battery during the transmission process.
If the battery is weak, the LED blinks during transmission.

Replacing the Battery

Insert a small coin into the notch on the top of the transmitter. Turn the coin diagonally and carefully pull the housing parts apart.
Replace the battery. Use only batteries of type CR2032. Observe the correct polarity!

Keep batteries out of reach of children!

Troubleshooting

The LED is only faint when lit up

Change the battery.

The LED does not light up at all

Check the polarity of the battery.

The receiver still does not respond

Move closer to the radio control or re-transmit the transmitter codes to the receiver.

Disposal

Waste electrical products and batteries should not be disposed of with household waste!

Dispose of the waste product via a collection point for electronic scrap or via your specialist dealer.

Dispose of used bat- teries in a recycling bin for batteries or via the specialist trade. Put the packaging material into the recycling bins for cardboard, paper and plastics.

Warranty

Within the statutory warranty period we undertake to rectify free of charge by repair or replacement any product defects arising from material or production faults.
Any unauthorized tampering with, or modifications to, the product shall render this warranty null and void.

Conformity

This product conforms to the basic requirements of the R&TTE Directive 1999/5/EG.
For use in: EU/CH/FL/IS/N The Declaration of Conformity can be found on the Internet at: www.eldat.de.

Customer Service

If, despite correct handling, faults or malfunctions occur or if the product was damaged, please contact the company at the address below:
ELDAT GmbH
Im Gewerbepark 14
15711 Königs Wusterhausen
Germany
Tel.: + 49 (0)3375 / 9037-0
Fax: + 49 (0)3375 / 9037-90
Website: www.eldat.de
E-Mail: info@eldat.de