Eldat RTS03 Manual

RTS03 Built-in transmitter multifunction
EN
Model
learning button PTx
LED
RTS03E5002C01
Technical details
Frequency: 868.30 MHz
Radiated power: 0.47 mW
Modulation: FSK
Coding: Easywave
POTA
Power consumption: 1x 3V-battery CR2032
OR
3V DC wired
Transmit current: approx. 12 mA
Stand-by current: approx. 2.5 μA
Range: free-field: approx. 150 m
builtings: approx. 30 m
Cable cross section: max. 1 mm²
Cable length: max. 3 m
Operating temperature: -20 °C to +60 °C
Dimensions (W/L/H): 33/36/14.5 mm
Weight: 10.0 g
Scope of delivery
Built-in transmitter, Battery CR2032, operating
instructions
Intended use
The built-in transmitter may only be used to oper-
ate Easywave radio controls.
The manufacturer shall not be liable for any dam-
age caused by improper or non-intended use!
Safety advice
Before using the device, carefully read
through the operating instructions.
- Never control moving devices or heaters
without observation.
- Note also the operating instructions of the
radio receiver.
- Have faulty devices checked by the manu-
facturer!
- Do not make any unauthorized alterations
or modifications to the transmitter!
- Do not connect an external 3V power supply
when a battery is inserted, risk of fire!
- The transmitter must not be connected to
230 V!
Function
With the built-in transmitter RTS03, the function-
ality of existing switches or buttons can be ex-
tended by a radio interface.
As soon as an input (S1, S2) is switched poten-
tial-free to GND, the RTS03 sends out a corre-
sponding Easywave code. Which transmission
code is sent depends on the operating mode set.
Buttons, switches and interlocked shutter switch-
es can be connected. The LED lights up red dur-
ing the transmission process.
Start-Up
1. Open the housing according to the section
"Inserting/changing the battery".
slide 2. Set the desired operating mode using the
switches
slide switches (see "Operating modes" sec-
tion).
3. Connect the buttons or switches to the termi-
nals S1 / S2 and GND according to the con-
nection diagram.
4. Insert the battery OR connect an external 3V
power supply to the GND and +3V DC termi-
nals.
5. Close the housing again.
If an external power supply is connect-
ed, DO NOT insert a battery!
Mounting advice
Mount the transmitter at a suitable location. Avoid
mounting at the following locations, as this may
affect the range of the transmitter:
− in a distribution box or housing made of
metal
− in the immediate vicinity of large metal ob-
jects
− on the ground (or near it)
Operating modes
The operating modes of the RTS03 can be select-
ed using the desired setting on the slide switch.
In order to change the operating mode, the power
supply must be interrupted or the battery must be
removed briefly. Otherwise, changes will not be
applied.
The operating modes can be set using the slide
switch positions described below:
PUSH-BUTTON
Suitable receiver operating modes:
- ON/OFF (1-button operation)
- DEAD MAN
- PULSE
- TIMER
- ON/OFF (2-button operation S1+S2)
- UP/DOWN (2-button operation, S1+S2)
SWITCH
Suitable receiver operating modes:
- ON/OFF (2-button operation)
- LOGIC
SHUTTER-CONTROL
Suitable receiver operating modes:
- UP/STOP/DOWN (3-button operation)
(factory setting)
ON
1 2
1:ON
2:OFF
ON
1 2
1:OFF
2:ON
ON
1 2
1:ON
2:ON
Connection diagrams
PUSH-BUTTON
PTx
S2 S1
Transmission lasts as long as a connected button
is pressed but max. 36 seconds.
push-button 1: input S1
push-button 2: input S2
In this mode only one input may be
switched at the same time! If both inputs
are closed at the same time, the trans-
mission process is blocked until BOTH
inputs have been opened again.
SWITCH
S1
PTx
S2
The transmission starts on every change of state
of a connected switch and lasts approx. 0.5 sec-
onds.
switch 1: input S1
code A
close switch:
code B
open switch:
switch 2: input S2
close switch: code C
open switch: code D
SHUTTER-CONTROL
S1
UP
AUF
DOWN
ZU
PTx
S2
The transmission starts on every change of state
of a connected switch and lasts approx. 0.5 sec-
onds.
switch 1: input S1
close switch: code A
open switch: code C
switch 2: input S2
close switch: code B
open switch: code D
ON
1 2
code A
code B
ON
1 2
ON
1 2