Parkside PBLS 26 A1 Operating And Safety Instructions Manual page 35

Note
Never immerse the device in water or other liquids for cleaning.
• Keep protective devices, air vents and the engine housing
as free of dust and dirt as possible. Blow it out with low-
pressure compressed air.
• To reduce the risk of fire, regularly clean the cooling fins of
the engine with compressed air. Clear the silencer area of
dust, leaves or other foreign objects.
• Clean the device at regular intervals using a damp cloth
and a little detergent. Make sure that no water can pen-
etrate the device interior.
When used as a leaf blower:
• Clean the blast pipe (4) and flat nozzle (1) / round nozzle
(2) with a brush when dirty.
When used as a leaf vacuum:
• After finishing work, remove the collection bag (24), turn
it inside out and clean it thoroughly and dry it if necessary
to prevent mould and unpleasant odours from developing.
• A heavily soiled collection bag (24) can be washed with
soap and water and then dried.
• If the zip is difficult to operate, rub the zip teeth with a dry
soap bar.
• Clean the vacuum tube (14), suction nozzle (12) and outlet
tube (18) with a brush if they are dirty.
13.2 Maintenance
CAUTION
Always switch off the device and disconnect the spark plug
connector before maintenance work (see chapter 13.2.2
Spark plug maintenance).
All protective and safety equipment must be reassembled im-
mediately after repair, maintenance is completed.
13.2.1 Carburettor setting maintenance
If the engine stops by itself when the throttle is released, a
carburettor adjustment must be made.
Have carburettor adjustments (e.g. idle speed adjustment) car-
ried out only by qualified specialists to avoid engine damage.
13.2.2 Spark plug maintenance (Fig. 14, 15, 16)
1. Remove the spark plug connector cover (17). To do this,
loosen the screw (H). (Fig. 14, 15)
2. Pull off the spark plug connector (30).
3. Loosen the spark plug with the enclosed spark plug
wrench (28).
Electrode gap = 0.6 - 0.7 mm (distance between the elec-
trodes, between which the ignition spark is generated).
Check the spark plug for dirt and grime after 10 operating
hours and if necessary, clean it with a copper wire brush. Then
service the spark plug every 50 operating hours.
4. The re-assembly takes place in reverse order.
30 GB
13.2.3 Fuel filter maintenance
Inside the fuel tank (22) there is a filter that prevents impurities
from entering the engine. The filter should be replaced once a
year by your dealer.
13.2.4 Air filter maintenance (fig. 14, 17)
Fouled air filters diminish the engine output due to reduced air
supply to the carburettor.
Regular inspection is therefore essential. The foam insert (31),
non-woven insert (32) and the metal insert (33) should be
checked regularly and cleaned if necessary.
If the air is very dusty, check the foam insert (31), non-woven
insert (32) and the metal insert (33) more frequently.
1. Loosen the air filter screw (26) by turning anti-clockwise.
2. Remove the cover (25).
3. Remove the foam insert (31), non-woven insert (32) and
the metal insert (33).
4. Clean the foam insert (31), non-woven insert (32) and the
metal insert (33) by knocking or blowing them out (with
compressed air).
5. The re-assembly takes place in reverse order.
WARNING
Never clean the air filter foam insert (31), air filter non-woven
insert (32) or the air filter metal insert (33) with petrol or flam-
mable solvents.
13.3 Important note in the case of repairs:
When returning the device for repair, for safety reasons, en-
sure that it is free of oil and fuel when it is sent to the service
centre.
13.3.1 Draining the fuel-oil mixture
In case of storage over a longer period of time, the petrol must
be drained.
Only empty the tank outdoors or in well-ventilated rooms.
Make sure that no fuel gets into the soil (environmental protec-
tion). Use a suitable collection container (not included in the
scope of delivery).
• Unscrew and remove the tank cover (23).
• Carefully pour the fuel-oil mixture from the tank into a suit-
able container.
• Drain the fuel-oil mixture completely.
• Screw the tank filler cap (23) back on by hand.
13.3.2 Ordering spare parts
Please provide the following information when ordering spare
parts;
• Device type
• Device article number
Service information
With this product, it is necessary to note that the following
parts are subject to natural or usage-related wear, or that the
following parts are required as consumables.
Wearing parts*: Spark plug, air filter, fuel filter, collection bag
* may not be included in the scope of supply!