Download
Share
Print this page
Velleman K8096 Manual
  1. Manuals
  2. Brands
  3. Velleman Manuals
  4. Computer Hardware
  5. K8096
  6. Manual
Velleman K8096 Manual

Velleman K8096 Manual

1-channel usb stepper motor card
Hide thumbs

Advertisement

Quick Links

Download this manual
K8096
K8096
ILLU
ILLUSTRATED ASSEMBLY MANUAL H8096IP'1
LLU
LLU
LLU
LLU
LLU
LLU
LLU
LLUSTRA
LLU
LU
LU
LU
LU
LU
STRA
STRA
STRA
STRA
STR
STRA
STRA
STRA
STRA
STRA
STRA
STRA
A
A
TED
TED
TED
TED
TED
TED
TED
TED
TED
T ED
TED
T
T
TED
ED
ASS
ASSE
ASS
AS
ASS
ASS
ASS
ASSE
ASSE
ASS
ASSE
ASSE
ASSE
ASSE
ASSE
ASSE
S
SE
E
M
MB
MBL
MBLY
MBLY
BLY
B LY
BLY
BLY
BLY
BLY
BLY
BLY
BLY
LY
LY
LY
1- Channel USB
1- Channel USB
stepper motor card
stepper motor card
MAN
MAN
MAN
M AN
MAN
M
M
M
M
M
M
M
MAN
MAN
M
M
ANUAL
UAL
UAL
UAL
UAL
UAL
UAL
UAL
UAL
UAL
UAL
UAL
UAL
U
UAL
AL
H809
H809
H809
H809
H809
H809
H809
H 809
H
H809
8096IP'
6I
6 IP
6
6IP'
6IP'
6IP'
6IP'
6IP'
6IP'
6IP'
6IP'
6IP'
6IP'
IP'
IP'
1
1
1
1
1
1
1
1
1
1
1
1
1
1
With the K8096 1-channel stepper motor card you can drive
1 stepper motor via USB, and monitor and assign actions if
needed to 5 dry contacts
(for example an emergency stop signal, current
limit detection).
Optional stepping motor: MOTS3

Advertisement

loading
Need help?

Need help?

Do you have a question about the K8096 and is the answer not in the manual?

Questions and answers

Related Manuals for Velleman K8096

Summary of Contents for Velleman K8096

  • Page 1 1- Channel USB stepper motor card stepper motor card With the K8096 1-channel stepper motor card you can drive 1 stepper motor via USB, and monitor and assign actions if needed to 5 dry contacts (for example an emergency stop signal, current limit detection).
  • Page 2 Subscribing our newsletter?, visit www.vellemanprojects.eu Forum Forum Participate our Velleman Projects Forum...
  • Page 3 With the K8096 1-channel stepper motor card you can drive 1 stepper motor via USB, and monitor and assign actions if needed to 5 dry contacts (for example an emergency stop signal, current limit detection). There is 1 open collector output that can be switched via USB. Write your own application (.DLL in- cluded).
  • Page 4 Leds and how to use them Leds feature a specifi c voltage Never connect leds in parallel drop, depending on type and colour. Check the datasheet for exact voltage drop and rated current ! How to Calculate the series resistor: series resistor: Example: operate a red led (1.7V) on a 9Vdc source.
  • Page 5 assembly 1. Assembly (Skipping this can lead to troubles ! ) hints Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: • A good quality soldering iron (25-40W) with a small tip.
  • Page 6 DO NOT BLINDLY FOLLOW THE ORDER OF THE COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR VALUE ON THE PARTS LIST! - 6 -...
  • Page 7 Construction Resistors Ceramic Capacitors Trimmer  ..C6 : 100nF (104) Adjust trimmer for RV...  C7 : 100nF (104) apropriate output R...  C12 : 100nF (104) current.  C13 : 100nF (104)  RV1 : 10K Ceramic Capacitors Diodes ...
  • Page 8 Construction Board to wire Terminal Block  SK1 : 2p (AC power 10 -30V) Watch the position Watch the position of the notch! of the notch!  SK4 : 4p (MOTOR) Quartz crystal  SK5 : 2p (IN)  IC1 : VK8096 (programmed PIC18F14K50-I/P) ...

  • Page 9: Software Installation

    Software installation 19. SOFTWARE INSTALLATION After assembly of the circuit, it is now time to install the software. For software, visit www.vellemanprojects.eu ownload the software on our Step 2: open the fi le en select the software. Step 3: Select “next” to begin the installation Step 1: D procedure.
  • Page 10 Software installtion Step 8: Select the additional tasks you would Step 7: Select “install” for installing the Step 9 : Click “fi nish” to exit setup. like, then click “next”. software. - 10 -...

  • Page 11: Driver Installation

    Driver installation 20. DRIVER INSTALLATION Connect the USB connector of the K8096 to your PC using an USB cable. With the fi rst connection, you should install the USB driver of the Stepper Motor Card onto the PC fi rst.

  • Page 12: Connection Diagram

    Connection diagram 21. CONNECTION DIAGRAM ex. optional stepping motor: MOTS3 1 open-collector INPUT output external power supply Min. 5V Max 30V ex. limit switch ex. alert switch - 12 -...
  • Page 13 Right: Let the motor turn to the right according to the selected number of steps. This but- will turn right for a periode. Reset the card by activating ton lights when the motor runs or stops. input 1 & 2 simulataneous. * The fi rst channel is only active if K8096 is selected. - 13 -...
  • Page 14 - 14 -...
  • Page 15 Diagram μ μ μ μ μ I / - - 15 -...
  • Page 16 The new Velleman Projects catalogue is now available. Download your copy here: www.vellemanprojects.eu Modifi cations and typographical errors reserved - © Velleman nv. H8096’IP 5 410329 474720 Velleman NV, Legen Heirweg 33 - 9890 Gavere.