Subscribe to Our Youtube Channel
Related Manuals for Velleman PIC K8076
Summary of Contents for Velleman PIC K8076
- Page 1 Total solder points: 202 Difficulty level: beginner 1 advanced PIC® programmer board K8076 ILLUSTRATED ASSEMBLY MANUAL H8076IP-1...
- Page 3 This device complies with Part 15 of the FCC Rules provided the enclosed instructions are followed to the letter. Use of the device is subject to the following conditions: (1) this device must not cause harmful interference and (2) the operation of this device should not be influenced by unwanted interference.
- Page 4 Features & Specifications Features: onboard configurable 40 pin. ZIF socket Microcontroller selection using patch jumper easy to use programming PICprog2006 software included SUBD connector set included Specifications: power supply: 15V DC, min. 300mA adapter (Ex. PS1508) serial port connector: 9 p. SUBD dimensions: 132x65x20mm / 5,23 x 2,57 x 0,79"...
- Page 5 Assembly hints 1. Assembly (Skipping this can lead to troubles ! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully. 1.1 Make sure you have the right tools: • A good quality soldering iron (25-40W) with a small tip.
- Page 6 Assembly hints 1.3 Soldering Hints : 1- Mount the component against the PCB surface and carefully solder the leads 2- Make sure the solder joints are cone-shaped and shiny 3- Trim excess leads as close as possible to the solder joint REMOVE THEM FROM THE TAPE ONE AT A TIME ! AXIAL COMPONENTS ARE TAPED IN THE COR- RECT MOUNTING SEQUENCE !
- Page 7 Construction 1. Diodes. Watch the polarity! 3. Metal film resistors 5. Capacitors D1 : 1N4007 R... D... D2 : 1N4148 CATHODE D3 : 1N4148 D4 : 1N4148 R10 : 47 (4 - 7 - 0 - B - 9) C1 : 100nF (104, u1) R11 : 220 (2 - 2 - 1 - B - 9) C2 : 100nF (104, u1)
- Page 8 Construction 12. Board to wire connector 7. Transistors. 10. Headers T1 : BC547 T2 : BC557 8. Voltage regulator SK3 : 5 poles SK4 : 5 poles VR2 : UA78L05 13. Electrolytic Capacitor. SK5 : 20P VR... Watch the polarity ! SK6 : 20P C4 : 10µ...
- Page 9 Construction 14. Sub D - connector 16. IC’s. Watch the position of the notch! SK2 : RS232 (9p female) IC1 : MAX232 15. ZIF socket IC2 : CD4049 17. Rubber feet Mount the rubber feet on the solder side of the PCB, see fig 1.0. SK5 : 40p FIG 1.0...
- Page 10 Construction 18. Serial cable Mount a SUBD connector on both sides of a shielded 6-core cable. Refer to fig. 2.0 below. SUBD 9-POLE MALE SUBD 9-POLE FEMALE FIG 2.0 If you do not assemble cables with the included SUBD connectors, pay attention to the following: all conductors must be connected “...
- Page 11 Construction Now, mount a enclosure over each SUBD connector according to fig. 3.0 FIG 3.0...
- Page 12 Software 19. PIC - selection cable Cut off a piece of each wire of the female 'board-to-wire' connector so there is 6cm of wire left on the connector. See fig. 4.0 Cut off 5 pieces of shrinkable tube with a lenght equal to 1cm. Slide the shrinkable tube over the wires of the female 'board to wire'-connector (fig.
- Page 14 Schematic diagram 21. Schematic diagram. +VPP UA7812 UA78L05 +VPIC +VPIC FB47 1N4007 100n 100n 220µ F/35 10µ F 10µ F 100n 15V DC 1N4148 IC2F +VPIC 1N4148 CD4049B ICSP1 ICSP2 IC2B IC2D MAX232N 1µ Fµ 1µ Fµ 1µ IC2E 1µ Fµ T1IN T1OUT IC2C...
- Page 15 22. PCB...
- Page 16 VELLEMAN Components NV Legen Heirweg 33 9890 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Modifications and typographical errors reserved © Velleman Components nv. H8076IP'1 - 2006 5 4 1 0 3 2 9 3 5 3 3 5 3...
Need help?
Do you have a question about the PIC K8076 and is the answer not in the manual?
Questions and answers