Advertisement
Quick Links
VICAT SOFTENING POINT TEMPERATURE TESTER
Thank you for your esteemed company to buy our products.
The operation is simple to use, but the wrong operation will cause the accidents and shorten the life of the
device or reduce its performance. Therefore, please be sure to familiarize yourself with this manual before use.
Please keep this manual.
OPERATION MANUAL
XB-OTS-VIKA10
Advertisement
Summary of Contents for OTS XB-OTS-VIKA10
- Page 1 VICAT SOFTENING POINT TEMPERATURE TESTER OPERATION MANUAL XB-OTS-VIKA10 Thank you for your esteemed company to buy our products. The operation is simple to use, but the wrong operation will cause the accidents and shorten the life of the device or reduce its performance.
- Page 2 Security Marks In this manual, there are following marks for security in operation. To avoid accidents and hazard, please obey the following precautions, warnings and notes: Danger This mark means workers may be hurt if he does not comply it. Warning This mark indicates the machine is possible to be damaged if it is not used by the right instructions.
- Page 3 4. Dial indicator support rod 5. Touch screen controller 6. Chassis 7. Mechanical over-temperature protection 8. Power switch 9. Stirring motor speed controller 10. Foot 1.4 Main technical parameters: Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 4 2.1.2 Check the attached accessories one by one according to the packing list. If the attached accessories do not match the packing list, please contact our company in time. 2.2 Hardware installation: Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 5 3.1. After the thermal deformation and VEKA softening point temperature detection equipment is powered on, the test system enters the following figure after completing the self-test: Click on "About..."Button to enter the system information interface, as shown in the figure below Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 6 When measuring the instrument, please follow the steps below to ensure the accuracy of the instrument. 3.3 Temperature measurement Temperature calibration needs to use temperature measuring instruments, click "temperature measurement" to enter the calibration interface, as shown below: Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 7 50 ° C, click the "Calibration" button twice successively, and the system will indicate that the calibration is successful and the current point calibration is completed. Then enter "100" and wait for the calibration of the next point. Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 8 Please refer to the instrument manual for the installation method. Click the "Deformation Measurement" button to enter the Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 9 "start test" button to start heating control. After 12 minutes, record the temperature difference at every 6-minute interval, and the error is within ±0.5℃ to be qualified. Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
-
Page 10: Testing Method
According to GB/T1633 or ISO306:1994 test method standard cut sample. The thickness of the sample should be (3～6.5)mm, a square sample with a side length of 10mm, or a round sample with a Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net... - Page 11 Before measuring the Vicat softening point temperature, please prepare the sample, perform pretreatment, measure the size of the sample, then install the sample, click the "Vicat determination" button to enter the interface as shown in the figure below Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 12 According to the test requirements, enter the appropriate heating rate, directly enter the mass of the loaded weight, or click the "Calculate" button to enter the interface as shown in the figure below: Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 13 "Back" button Return to the test interface. Testing method total weight(N) Need to add weight(g) Method A 10*1000/9.81 - 68= 951 Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 14 "thermal deformation measurement" button to enter the thermal deformation measurement interface, as shown in the following figure: Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 15 "flat" or "side stand", enter the corresponding bending stress, click the "calculate" button again, and the corresponding weight will be displayed. Enter the span and deflection, click "Back" to return; Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 16 Testing Need to add weight Sample size（l×b×h） pressure,MPa Load,N method method F1,g flat (3/9.81) ×1000-68 = 80mm×10mm×4mm 1.80 (recommended) Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 17 R—load bar weight + pallet weight + pressure needle (indenter) + sensor axis (70g) If there are two sets of sample holders, check the two deformations corresponding to the installed samples, and click "Start Test" to start temperature control; Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...
- Page 18 5. During the high temperature test, a small amount of volatile smoke will appear (most obvious above 200℃), please do a good job of ventilation and smoke exhaust. Add: The 3rd Industrial Zone, Chashan Town, Dongguan. Tel: 0769-33365786 www.ots-testequipment.net...