Subscribe to Our Youtube Channel
Related Manuals for Carrier 2X-A/2X
Summary of Contents for Carrier 2X-A/2X
- Page 1 UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels P/N 10-9000-501-UC24-02 • ISS 17NOV22...
- Page 2 Copyright © 2022 Carrier. All rights reserved. Trademarks and UC240 UltraSync Communicator is a trademark of Carrier. patents Other trade names used in this document may be trademarks or registered trademarks of the manufacturers or vendors of the respective products.
-
Page 3: Table Of Contents
Installation 2 Wiring 5 Control panel configuration and UC240 programming 7 Control panel configuration 7 UC240 quick programming guide 8 UC240 commissioning checklist 11 Mapping events 12 UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels... -
Page 4: Important Information
Note messages advise you of the possible loss of time or effort. They describe how to avoid the loss. Notes are also used to point out important information that you should read. UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels... -
Page 5: Installation
Once registered with the Carrier UltraSync portal, the UC240 allows notifications to be sent to: • Central Monitoring Stations (CMS) • Email addresses • Supported mobile apps (IOS and Android) Figure 1: UC240 Communicator UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels... -
Page 6: Installation
If direct glanding is not possible, interface cables should be enclosed in conduits to provide mechanical protection. Once all wiring is completed, secure the lid to the SMB-DIN2 using the screws provided. UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels... - Page 7 The device can be programmed via the device interface or the UltraSync+ mobile app (available for Android and IOS mobile devices). See “Configuration Utility configuration and UC240 programming” on page 7 for information on configuration and programming. UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels...
- Page 8 Figure 3: SMB-DIN2 lid screws Figure 4: UC240 installation (DIN rail) Figure 5: UC240 installation (inside lid) Figure 6: UC240 installation location Figure 7: UC240 installation location UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels...
-
Page 9: Wiring
See Figure 9 on page 6 for interfacing fault input. • See “Fire routing delay configuration for the 2010-2-PIB” on page 8 for fire routing delay configuration. UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels... - Page 10 Event reporting only. This option is compatible with any 2X-A/2X, KFP-A, ZP2- A/ZP2 control panel variant. Figure 9: Non-EN 54-21 compliant option (panel inputs, fire and fault relay outputs) UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels...
-
Page 11: Control Panel Configuration And Uc240 Programming
Table 3: Input 2 (only for EN 54-21 installations) Parameter Configuration OpMode Fire Routing Ack Type 1 Control Enabled Description Dialer/CMS Ack Zone None Figure 11: Configuration Utility Input 2 configuration UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels... - Page 12 Configuration window (Group ID 971), as shown below. The delay must be configured for each zone. Figure 13: Configuring the fire routing delay in the Zone Configuration window UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels...
-
Page 13: Uc240 Quick Programming Guide
5. Go to Output Type and change the Output3 setting to Fire Ack. Press ↵ for 3 seconds to save. 6. Write down your SID number and Web Pass Code in a safe place. Figure 14: Web pass code location UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels... - Page 14 Figure 15: Programming menus Figure 16: Signal strength UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels...
-
Page 15: Uc240 Commissioning Checklist
UC240 commissioning checklist Figure 17: Path: Mobile Registered Figure 18: Mobile1 Strength Figure 19: Mobile1 Operator Figure 20: Service Grade Figure 21: Path: Ethernet Registered UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels... -
Page 16: Mapping Events
(System Trouble). R323908 should be R300908 (Alarm Relay). Surgard SIA BA908 BA908 BR908 Should be SIM 2/4G FT908 (Fire Trouble). BR908 Should be FR908 (Fire Restoral). UC240 UltraSync Communicator Installation Guide for 2X-A/2X, KFP-A, and ZP2-A/ZP2 Fire Alarm Control Panels...
Need help?
Do you have a question about the 2X-A/2X and is the answer not in the manual?
Questions and answers