Kenwood DDX512 Service Manual page 18

DDX5022/5022Y/5032/5032M/512/52RY
DNX5120/512EX/5220/5220BT
3.4 Serial No. Entry screen
Enter the serial code of each set from this screen.
The Serial No. Entry screen is shown in Figure 3.4.
Serial Number Input
– – – – – – – –
1 2 3
4 5 6
7 8 9
0
Clear Cancel
Figure 3.4 Serial No. Entry screen
Key Specifi cation
0~9 : 10key used to enter the serial No.
Clear : Clear the serial No. being input.
Cancel : Transfer to Service screen
Enter : Start entering the serial No.
(When the entry is successfully completed, the
"Write OK" is shown. When the entry is not suc-
cessfully completed, the "Write NG" is shown)
When the "Write OK" is shown, use this key to
transfer to the Service screen.
If the "Write NG" is shown, transfer to the Test
mode again and repeat the entry from the first
step.
3.5 DVD Service Information screen
This screen is to show DVS-8000 service information. This
screen is also used to transfer to DVS-8000 Adjustment
screen.
The DVD Service screen is shown in Figure 3.5.
DVS-8000 Service Information
DVS-8000 Adjust
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
Return
Next
Figure 3.5 DVD Service Information screen
Key Specifi cation
DVS-8000 Adjust : Transfer to DVS-8000 Adjustment screen
Next : Transfer to next DVS-8000 Service In-
formation screen.
Return : Transfer to Test Mode Main screen
18
TEST MODE
Serial Number Input
∗ ∗ ∗ ∗ ∗ ∗ ∗ ∗
Clear Cancel Enter
DVS-8000 Service Information
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
∗∗∗∗∗∗∗∗∗∗
Return
3.5.1 DVS-8000 Adjustment screen
This is to display DVS-8000 Servo Adjustment screen.
Refer to the Mechanism Specifi cation for the detail setup.
DVS-8000 Adjust DVS-8000 Adjust
Offset Cancel
Inner Limit
Adjust Start
Focus Height
Return
Figure 3.5.1 DVS-8000 Adjustment screen
Key Specifi cation
Offset Cancel : Adjust the offset cancel.
Inner Limit : Adjustment of inner circumference limit
Focus Height : Adjustment of focus height
Adjust Start : Start of adjustment
Return (the First screen) : Tr a n s f e r t o Te s t M o d e M a i n
screen.
Cancel/Return : Transfer to DVS-8000 Adjust screen (Ini-
tial screen).
3.6 Tuner Mute Level screen
Adjust the Mute Level stored in the E2PROM of the Tuner F/E.
The Tuner Mute Level Setup screen is shown in Figure 3.6.
Tuner Mute Level
DW UP
∗∗∗∗
Cancel
■ Write
Figure 3.6 Tuner Mute Level Setting screen
Key Specifi cation
UP : Mute Level Up
DW : Mute Level Down
■Write : Press and hold (for 1 seconds or longer) to make
the entry in the E2PROM.
Return : Transfer to Service screen.
∗ Adjust the Tuner Mute Level under the following condi-
tions. Under the other conditions than the followings, the
Tuner Mute Level cannot be adjusted if the Tuner Mute
Level Setup screen is shown.
The frequency shall have to be set before transferring to
the Setup screen.
Audio Source : Tuner
LOUD : OFF
Volume : Step30
DVS-8000 Adjust
Adjust OK/NG
Cancel Return
Tuner Mute Level
Wite OK/NG
Return