LEXIBOOK BTP180 Series - Wireless Light Speaker With Mic Manual

LOCATION OF CONTROLS

1. Handle
2. Speakers
3. Microphone
4. Speakers volume knob
5. Mic volume knob
6. Mic echo knob
7. Backward button
8. Play/Pause button
9. Forward button
10. Light button
11. On/Off button
12. USB port for audio playback
13. TF cart slot
14. Aux-in jack
15. USB Type C charging port
16. Mic jack 6.5mm

POWER SUPPLY

The speaker operates with the USB Type C charging cable (included) or with a USB type adaptor (not included) 5.0V, 1.0A. Input: 100 ~ 240V, 50/60 Hz.

Power supply

1. Check that the unit is switched off.
2. Insert the small end of the USB Type C cable (included) into the USB Type C charging port (15) on the back of the unit.
3. Connect the other end of the USB Type C cable into the USB port of your powered computer or USB type power adaptor and connect it to a wall socket. The LED near the USB Type C charging port lights up in red when the device is charging.
4. Once charging is completed, the LED light will turn off.

Note: Please note that the USB Type C cable can be used for battery charging only and not for data transfer.

• Danger of explosion if battery is incorrectly replaced. Please only replace it with the same or equivalent battery.
• Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
• 
  Mal-function or loss of memory may be caused by strong frequency interference or electrostatic discharge. Should any abnormal function occur, switch it off and then on again, or unplug the USB cable.

FUNCTIONS & MODES

To turn the speaker on/off, slide the on/off button (11) at the back of the product. A signal will sound to notify the device is ready.
To adjust the volume, turn the volume button on the top of the product (4).

MODES

The speaker includes different modes: Bluetooth®, USB, TF card (up to 32GB), and AUX in.

• To change mode, long press the play/pause button (8). A signal will sound every time you switch modes.
• In Bluetooth® delete, USB and TF modes, press Previous, Play/Pause and Next buttons (7, 8, 9) to control your audio files.
• In AUX-in mode, these buttons are disabled. Please use the control buttons on your music player.
• You can sing by connecting the microphone (included) to the Microphone jack (16). Control the mic volume and echo effect using the top knobs (5) & (6).

BLUETOOTH® PAIRING

1. Activate the Bluetooth function on your personal device and make sure it is in discoverable mode.
2. Confirm pairing or select the Bluetooth name "BTP180" to connect your player to the speaker.
3. You can play an audio or a video file. The speaker will issue a sound after it has connected successfully.
4. To stop the connection with the speaker, press another mode on the top panel or a button on your audio player. Once the connection has been stopped, the LED indicator will flash.

Note: Some music players do not fully support Bluetooth® audio controls. Play/pause, previous and next buttons on the Bluetooth® speaker may not respond. The music player may also turn off. To get the best control experience in the said player, use the on-screen track controls of your music player rather than those on the speaker.

CONNECT 2 SPEAKERS IN STEREO

You can connect two BTP180 speakers together to enjoy stereo sound (available only in Bluetooth mode):

1. Delete the BTP180 speaker on your Bluetooth history in your mobile.
2. Turn on two BTP180 speakers simultaneously.
3. Activate the Bluetooth® function of your audio player and confirm the pairing to the speaker (BTP180) as explained in the previous section.

LIGHT EFFECTS

Press the light button (10) to turn the light effects on/off.

Too high volume can damage your hearing. For this reason, lease turn the volume down.

SPECIFICATIONS

Input power: USB DC 5.0V 1.0A
Battery: Lithium battery 3.7V, 1200mAh
Bluetooth Frequency range: 2402-2480MHz
Transmission power: 0.44 dBm EIRP