1. DISASSEMBLING PROCEDURES 1-2. Notes on Assembling and Disas- 1-1. Disassembling Procedures sembling 1. Remove the battery and the SmartMedia. 1. Be sure to discharge the condenser of strobe to 2. Remove five screws and two tripod fixing screws. prevent electric shock. Open the DC jack cover and remove the rear cover 2.
2. OUTLINE OF ELECTRICAL CIR- CUIT 2-1. System Over View It consists of 5 PC boards, lens module, color LCD and mode dial. Microprocessor unit detects the power management and key operation and functions as a slave microproc- essor of DSP (Raptor) in the Logic unit. Logic unit covers all functions of signal processing and camera functions.
Page 5
U100 Logic Unit FLASH RAM SD RAM (M29W400BT90) (HY57V651620) H001 Lens Module IR filter CDS/AD I_Data(10bit) U25A Buffer CCD control V&HDriver LCD Drv PU1,PU2 LCD_Data (EM1812B) (MB87J33020) U25B Iris Zoom Focus Color LCD J0402 FLASH SM socket CN015P-2103-1 A240 Mode Dial FLASH_ENb POWER_EN,BACK_CUR,etc U400...
2-2. Boot up Sequence 2-3. OFF Mode Chart2 Boot Up When Pin4 (J501 Pin7) PWR_SWITCH signal (U302 Pin2) of the mode dial (SW502) develops high, the The voltage of 3.3V_UC is supplied by a battery microprocessor enters OFF mode. insertion or DC input. The microprocessor (U302) is In the OFF mode, the microprocessor turns all the reset and starts the boot-up operation of DSP (U20).
2-5. LCD 2-11. Strobe Control After the images stored on the SDRAM (U21) are Strobe charge is controlled by a sub microprocessor processed inside DSP (U20) again, they are modified and the light emission is controlled by DSP (U20) to the appropriate size, bit width (6 bit per each RGB) corresponding to the CCD output amount.
3. ELECTRICAL ADJUSTMENT Calibration Procedures – PDR-M60 Equipments 1) Light Box: DNP Standard Color Viewer Model: CCV51F Use Lamp: FL-10W-4 Voltage : 100V 2) Vector Scope 3) Focus Test Charts Supplied from TOSHIBA. Near Focus Chart Supplied as PDF file.
Page 9
Select item 1 named CCD calibration used Mode dial. Item number is shown on a status LCD. ”Manual Rec” mode shown as items 1 on B/W LCD. Press shutter to run CCD Calibration Test If Color LCD display “** OK **”, Camera Passes Record Data to Traveler Sheet and Pass to next station. If Color LCD display “** Error ???**”, Camera Fails, record failure code and submit to Failure Analysis.
Page 10
Near Focus Verification Tools: DNP Light Box Power Supply (AC adaptor 5V) Camera Positioning Fixture 40 cm Focus Target attached to light box Smart Media card with Calibration Code Procedure: Install Smart Media card with Calibration Code into camera. Place camera into the positioning fixture. Positioning Fixture slides right to left at Preset Detents to hit the 40cm targets.
Page 11
5) Smart Media card with Calibration Code Procedure: Install Smart Media card with Calibration Code into camera. Place camera into the positioning fixture. Positioning Fixture slides right to left at Preset Detents to hit the 3 m targets. Attach camera to power supply. Point camera at the 3 m Focus target. Turn on camera Select Item 3 with Mode dial.
Page 12
Strobe Check Tools: Power Supply (Topward: DC Power Supply set to 5V) 18% Grey Chart (44 cm x 37cm) See Attachment “A” Camera Positioning Fixture Smart Media card with Calibration Code Procedure: Install Smart Media card with Calibration Code into camera. Place camera into the positioning fixture.
Page 13
Press shutter to display menu on CRT monitor. Select item 6 on the screen with T and W zoom button Press shutter to run a video calibration Use zoom T/W buttons until all spectral dots simultaneously match up each color boxes on the Vector scope.
Page 14
Press shutter to display menu on CRT monitor. Select item 7 on the screen with T and W zoom button Press shutter to run a LCD calibration. Use zoom T/W buttons until A,B,C,D bar are visible as separately. – 13 –...
Page 15
Attachment “A ” Strobe Check Box Specifications Entrance: Covered with Black Felt Curtains Dimensions: WxHxD'1 m x 1 m x 1 m Material: .75 inch thick Cabinet Grade Plywood Paint: Paint Interior Surface with Flat Black Paint 18 % Gray Rear Target: Fits Tightly to Rear Inside Dimension of Box.
Page 16
8. Firmware update using the USB 9. Firmware update using the cable SmartMedia Preparation: the latest firmware Preparation: SmartMedia with the latest [fware64.bin] copied PDR-M60 PDR-M60 AC adapter AC adapter USB cable Method: Method: Be sure to turn the camera to [OFF], remove the 1.
4. CIRCUIT DIAGRAM 4-1. Logic Unit Circuit Diagram VCCY +3.3V R 3 9 +3.3V LCD_GCP 2 . 7 K LCD_FRX LCD_ALRST +2.6V_RAPTOR R 4 0 D 3 3 B R 4 7 LCD_LP C 1 3 LCD_RES C 2 9 +3.3V_UC 1 0 0 HN2D01FU...