Wahl DC152B01 Operating Manual page 10

E N G L I S H
Type DC152B01
Power consumption:
Heating element diameter: 19 mm
Weight:
Type DC152C01
Power consumption:
Heating element diameter: 25 mm
de
Weight:
en
Type DC152D01
Power consumption:
fr
Heating element diameter: 32 mm
Weight:
it
The appliance is safety insulated and radio screened. It meets
es
the requirements of EU Electromagnetic Compatibility Direc-
tive 2014/30/EU and Low Voltage Directive 2014/35/EU.
pt
nl
Operation
da
Preparation
f Check that the contents are complete.
sv
f Check all the parts for possible transport damage.
no
Safety
fi
Caution! Damage due to incorrect power supply.
f Only operate the curling tong with the voltage
tr
stated on the nameplate.
pl
Operation
cs
1. Unfold the base stand and place the curling tong on a flat,
smooth, non-heat-sensitive surface.
sk
2. Insert the mains plug into the socket.
3. Hold the on/off switch down for 1 second to switch on the
hr
curling tong (Fig. 2). An acoustic signal will sound and the
LCD display will illuminate. The preset operating tempera-
hu
ture is identical to your previous setting.
4. Select the desired temperature (80 °C – 210 °C) (Fig. 3).
sl
· To increase the temperature, press the p button.
· To reduce the temperature, press the q button.
ro
· Tapping can adjust the temperature in 5 °C steps.
bg
To adjust the temperature more quickly, hold
ru
down the appropriate button.
· The LCD display flashes three times when the
uk
temperature is set. Once the set operating
temperature has been reached, the LCD display
et
shows the temperature.
lv
5. Switch off the curling tong after use. To do this, hold the
on/off switch down for 1 second (Fig. 2). An acoustic signal
lt
will sound and the LCD display will go out.
6. Disconnect from the mains.
el
10
ar
52 – 56 W
225 g without mains cable
66 – 69 W
315 g without mains cable
78 – 80 W
340 g without mains cable
7. Unfold the base stand and place the curling tong on a flat,
smooth, non-heat-sensitive surface.
8. Allow the curling tong to cool down.
Operation
Tips for successful styling
Warning! Burning hazards due to incorrect
handling.
f Only hold the curling tong at the cool tip and
the handle.
f Never touch the scalp with the hot curling tong.
f Always carry out a test on an individual section
of hair first.
1. Wash and rinse the hair well.
2. Dry the hair.
3. Brush or comb the hair.
4. Divide the hair into 2 cm thick and 4 cm wide sections.
5. Open the tong (Fig. 4) and place the tip of the hair section
on the heating element.
6. Close the tong. Hold the curling tong at the cool tip and
the handle, and curl the hair as desired. Ensure that the
hair is pulled taut.
7. For looser curls, leave the hair wrapped around the tong
for about 20 seconds.
8. Release the hair by gently rotating in the opposite
direction.
9. Open the tong and carefully pull the heating element off
the curl.
10. Repeat this process until the desired result has been
achieved.
11. The hair can be combed as soon as all curls have cooled
down.
TITANIUM coating
Negative ions have an antistatic effect and are gentle to the
hair. They close the scale layer, creating a smooth, silky hair
surface. They lock in the natural moisture of the hair, thereby
creating the ultimate shine.
Maintenance
Warning! Injuries and material damage due to
incorrect handling.
f Switch off the curling tong before cleaning them
or performing any maintenance. Disconnect the
curling tong from the power supply.
f Allow the curling tong to cool down completely.