Extron electronics DTP3 T 202 Setup Manual page 3

LockIt™ Lacing Brackets
Use an included LockIt lacing bracket to securely fasten an HDMI cable to each device as
follows:
1 Plug the HDMI cable into the panel connection.
2
Loosen the HDMI connection mounting screw from the panel enough to allow the
LockIt lacing bracket to be placed over it. The screw does not have to be removed.
3
Place the LockIt lacing bracket on the screw and against the HDMI connector, then
tighten the screw to secure the bracket.
ATTENTION:
• Do not overtighten the HDMI connector mounting screw. The shield it
fastens to is very thin and can easily be stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage
auquel elle est attachée est très fin et peut facilement être dénudé.
4
Loosely place the included tie wrap around the HDMI connector and the LockIt lacing
bracket as shown.
5
While holding the connector securely against the lacing bracket, use pliers to tighten
the tie wrap, then remove any excess length.
Front Panel Features
DTP3 T 202 Front Panel
CONFIG
e
A B
Figure 6. Front Panels of the DTP3 T 202 and DTP3 R 201
A Power LED — Lights green when the unit is receiving power, either locally or remotely (on the DTP cable).
B Configuration port — Using a USB cable, connect a PC to this front panel USB C port for remote operation using PCS and
firmware updates.
DTP3 T 202 Rear Panel
C SEND POWER toggle switch — In a DTP3 transmitter to DTP3 receiver configuration, set the toggle switch to the UP
(SEND POWER) position on the powered DTP3 device to enable sending remote power to a DTP3 device on the far end. Set
POWER HDMI HDMI
12V
the toggle switch to the DOWN (OFF) position on the DTP3 device receiving power (see
1.5A MAX
switch configuration).
LOOP OUT INPUT
ATTENTION:
• The DTP3 T 202 device is configured to output power to DTP3 models only. If connected to a Legacy DTP device,
A B C
set the toggle switch to the DOWN (OFF) position. Failure to turn the power OFF will damage the connected Legacy
DTP device.
• Le DTP3 T 202 est configuré pour fournir une alimentation aux modèles DTP3 uniquement. S'il est connecté à un
autre appareil, veuillez positionner l'interrupteur à bascule sur « DOWN » (OFF). Si l'interrupteur n'est pas positionné
sur OFF, vous risquez d'entraîner la défaillance de l'appareil Legacy DTP connecté.
NOTE:
DTP3 transmitters and receivers are compatible with Legacy DTP products. However, Remote Power must be
configured properly. Failure to do so will result in damage to the units (see
D HDBT/DTP toggle switch (Tx) — Configures the DTP3 Output for either HDBT or DTP mode.
E Front panel indicators
SIGNAL — Lights when the unit is receiving a TMDS clock signal on the Input connector (transmitter), or any valid
•
signal on the DTP3 In connector (receiver).
HDCP — Lights when the unit is receiving an HDCP‑compliant signal on the Input connector (transmitter), or any valid
•
signal on the DTP3 In connector (receiver).
NOTE:
The front panel LEDs are tied to the rear panel LEDs on the DTP connector (see
SEND
INPUT
PWR HDBT
SIGNAL
HDCP
OFF DTP
DTP3 T 202
C D E
SIG LINK OVER
TP
RS-232
G
OUT Tx Rx
D E
DTP3 R 201 Front Panel
SEND
PWR
CONFIG
e
OFF
A B C
DTP3 R 201 Rear Panel
SIG
POWER HDMI
12V
1.5A MAX
OUTPUT DTP3 IN
A F D
figure 7
1 1 1
3 3 3
4 4 4
3
5 5 5
INPUT
SIGNAL
HDCP
DTP3 R 201
E
LINK OVER
L R
DTP3
figure 7 on the next page for toggle
RS-232
G AUDIO OUT
Tx Rx
E G
on the next page).
D
figure 2, on page 1).
2 2 2
3