Specifications - Makita 2012NB Instruction Manual

ENGLISH (Original instructions)
1-1. Carrying handle
1-2. Sub-table
1-3. Carrying handle
2-1. Bolt or screw
3-1. Pilot lamp
3-2. Switch
4-1. Crank handle
4-2. Scale
4-3. Main frame
4-4. Indicator plate
5-1. Depth gauge
6-1. Crank handle
6-2. Groove
6-3. Depth adjusting gauge
7-1. Stopper
7-2. Stopper button
7-3. Stopper knob
7-4. Table top
8-1. Lock plate
8-2. Pulley
8-3. Drum
8-4. Chain
8-5. Thumb screw
9-1. Blade installation bolts
9-2. Set plate

SPECIFICATIONS

Max. cutting depth
Feed rate (min
Table size (W x L)
No load speed (min
Overall length (W x L x H)
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Explanation of general view
9-3. Magnetic holder
9-4. Drum
9-5. Blade
9-6. Claw
10-1. Socket wrench
10-2. Magnetic holders
11-1. Socket wrench
11-2. Lock plate
11-3. Blade installation bolt
12-1. Set plate
13-1. Magnetic holder
13-2. Set plate
13-3. Blade
14-1. Blade installation bolts
14-2. Set plate
14-3. Magnetic holder
14-4. Drum
14-5. Blade
14-6. Claw
15-1. Socket wrench
15-2. Magnetic holders
16-1. Screw
16-2. Set plate
16-3. Blade
16-4. Blade gauge
Model
Cutting width
-1
)
-1
)
Net weight
safety class
3.0 mm of stock width less than 150 mm
1.5 mm of stock width from 150 mm to 240 mm
1.0 mm of stock width from 240 mm to 304 mm
ENE001-1
For public low-voltage distribution systems of
between 220 V and 250 V.
ENF002-1
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.38 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
4
17-1. Set plate
17-2. Groove
17-3. Blade
17-4. Drum
18-1. Socket wrench
18-2. Lock plate
18-3. Blade installation bolt
19-1. Hood set
20-1. Thumb screw
20-2. Chip cover
20-3. Chain
20-4. Hood set
23-1. Ruler
23-2. Post card
23-3. Adjusting screw
24-1. Hex wrench
25-1. Limit mark
26-1. Brush holder cap
26-2. Screwdriver
27-1. Column
27-2. Screw
27-3. Chain
28-1. Base
28-2. Blade
28-3. More than 4 mm
2012NB
304 mm
8.5 m
304 mm x 771 mm
8,500
483 mm x 771 mm x 401 mm
28.1 kg
/II
ENF100-1