Danfoss Living Connect - Electronic Radiator Thermostat Quick Start Guide

Also See for living connect:

Installation and user manual (56 pages)

Datasheet (8 pages)

Installation and user manual (16 pages)

Table of Contents

Contents

1 Inserting the batteries
2 Installing living connect
3 Adding living connect to a system
4 Display and buttons
5 Testing the connection
6 Temperature control and adjustment
7 Technical specifications
8 Documents / Resources
- 8.1 References
- 8.2 Download manual

Danfoss Living Connect - Electronic Radiator Thermostat Quick Start Guide

living connect® is an electronic radiator thermostat for residential use with a Danfoss Link™ system (for further information on the system, please refer to Installation Guide for Danfoss Link™ CC central controller).

Inserting the batteries

Remove the battery cover and insert two AA batteries. Make sure the batteries are correctly oriented.

Rechargeable batteries must not be used.

When replacing batteries the programme settings will be preserved, but after two minutes the settings for time and date are reset.

Installing living connect^®

Installation

must be flashing on the display prior to installing.

Start by mounting the appropriate adapter.
Tighten RA adapter using the 2 mm Allen key, handtighten K adapter (max. 5 Nm).
Screw the thermostat onto the adapter and tighten by hand (max. 5 Nm).
A large flashes, press to fix living connect®.
For removing and re-installation, please refer to www.living.danfoss.com

Adding living connect^® to a system

The process of adding the living connect® to a system is performed on the Danfoss Link™ CC.

Note that the living connect® must be added to a room. When adding, press and release and observe that back light and antenna symbol are flashing. For further information, please refer to the Danfoss Link™ CC installation guide.

Display and buttons

Use to navigate the display and the menus and to set the temperature, and use to select and confirm.

Testing the connection

Press for at least 3 seconds until is displayed.

Press until is displayed.

Press to test the connection. disappears when the connection is made and a message is displayed on the Danfoss Link™ CC.

If no connection can be made, the alarm symbol and the antenna symbol flash.

Temperature control and adjustment

Press to change the temperature.

The temperature is usually controlled via Danfoss Link™ CC, but may be changed at any time using the thermostat's buttons.

If this is done, the thermostat sends a message to Danfoss Link™ CC, instructing it to synchronise the other thermostats in the same room.

Technical specifications

Thermostat type	Programmable electronic radiator valve controller
Recommended use	Residential (pollution degree 2)
Actuator	Electromechanical
Display	Grey digital with backlight
Software classification	A
Control	PID
Transmission frequency / range	868.42 MHz / up to 30 m
Power supply	2 x 1.5 V alkaline AA batteries
Power consumption	3 μW in standby 1.2 W when active
Battery life	2 years
Low batteri signal	Battery icon will flash in display. If battery level is critical, the whole display will flash.
Ambient temp. range	0 to 40°C
Transportation temp. range	-20 to 65°C
Max. water temp.	90°C
Temp. setting range	4 to 28°C
Measurement interval	Measures temp. every minute
Clock accuracy	+/- 10 min/year
Spindle movement	Linear, up to 4.5 mm, max. 2 mm on valve (1 mm/s)
Noise level	<30 dBA
Safety classification	Type 1
Weight (incl. batteries)	177 g (with RA adapter)
IP class	20

Tested for safety and EMC requirements as specified in EN 0730-1, EN 60730-2-9 and EN 60730-2-14.

To see the full installation and user guide, go to www.living.danfoss.com or see videos about installation and programming on www.YouTube.com
- search for Danfoss living connect.

Safety precautions
The thermostat is not intended for children and must not be used as a toy.
Do not leave packaging materials where children may be tempted to play with them, as this is extremely dangerous.

Do not attempt to dismantle the thermostat as it contains no user-serviceable parts. If error code E1, E2 etc. is shown in the display or other defects appear, please return the thermostat to the distributor.

Danfoss A/S Haarupvaenget 11
DK-8600 Silkeborg
Denmark
Phone: +45 7488 8000
Fax: +45 7488 8100

Homepage: www.danfoss.com

Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.