System Config - Panasonic BT-LH900 Operating Instructions Manual

MAIN MENU

SYSTEM CONFIG

Item Setting
BACKLIGHT 0 For adjusting the backlight brightness to a
:
level from 0 to 60. The higher the setting,
60
the brighter the backlight.
FUNCTION WFM For setting the function to be allocated to
ON/OFF the FUNCTION/ENTER button.
HV DELAY WFM ON/OFF: The Y signal (luminance)
UNDEF
HV DELAY: The blanked parts of the
UNDEF:
WFM FUNCTION For selecting whether the Y signal
GPI (luminance) waveforms are to be displayed
using the FUNCTION/ENTER button or
from the GPI connector.
FUNCTION: The waveforms are displayed
GPI:
HD ZOOM FRONT For selecting whether the HD ZOOM
GPI function is to be operated using the HD
ZOOM/X button or from the GPI connector.
FRONT: The function is operated using the
GPI:
PEAKING/ PHASE PEAKING For selecting the PEAKING or PHASE
PHASE function for the image control.
PEAKING: The
PHASE: The PHASE function is allocated
USER MODE USER5 For calling the file in which the user data is
LOAD USER4 stored.
USER3 USER1-5:
USER2
USER1
FACTORY
FACTORY: This file contains the factory
USER MODE SAVE USER5 For saving the user data.
USER4
USER3
USER2
USER1
The underlined setting indicates the factory setting mode.
Description
waveforms are displayed.
images are displayed.
No function is allocated.
using the FUNCTION/ENTER
button.
The operations are performed
from the GPI connector. For
details, refer to "REMOTE
specifications" (page 22).
HD ZOOM/X button.
The operations are performed from
the GPI connector. For details,
refer to "REMOTE specifications"
(page 22).
PEAKING function is
allocated to the control.
to the control.
These are the files in which the
user has stored data. If the user
data has not yet been stored,
the settings are the same as the
ones in the FACTORY file.
settings.
OSD CONFIG
Item Setting
BATTERY REMAIN OFF For selecting whether to display the
ON remaining battery charge.
OFF: The remaining charge is not displayed.
ON: The remaining charge is displayed.
STATUS DISPLAY CONTINUE For setting how long the status display is to
3SEC. OFF remain on the screen.
OFF CONTINUE: The status display appears
3SEC.OFF: The status display appears for
OFF: The status display does not appear.
CRCC MESSAGE OFF For selecting whether a message is to be
ON displayed when a CRCC error has been
detected.
OFF: A CRCC error message is not displayed.
ON: A CRCC error message is displayed.
MENU POSITION LT For setting the menu display position.
CENTER LT: The menu is displayed at the top left.
LB CENTER:
RB
RT LB: The menu is displayed at the bottom left.
RB: The menu is displayed at the bottom right.
RT: The menu is displayed at the top right.
STATUS POSITION LT For setting the status display position.
CENTER LT: The menu is displayed at the top left.
LB CENTER:
RB
RT LB: The menu is displayed at the bottom left.
RB: The menu is displayed at the bottom right.
RT: The menu is displayed at the top right.
ROTARY LB For setting the display position of the
POSITION CB settings when images have been adjusted
RB using the image controls.
RT LB: The settings are displayed at the
LT
CENTER CB: The settings are displayed below the center.
OFF RB: The settings are displayed at the
RT: The settings are displayed at the top right.
LT: The settings are displayed at the top left.
CENTER:
OFF: The settings are not displayed.
GPI
Item Setting
GPI1-8 UNDEF
MARKER1 ON/OFF
MARKER2 ON/OFF
MARKER BACK HALF
MARKER BACK BLACK
CENTER MARKER
INPUT SEL. SDI1
INPUT SEL. SDI2
INPUT SEL. VIDEO
INPUT SEL. YPBPR/RGB
SD ASPECT
HD ZOOM
BACKLIGHT MIN.
R.TALLY
G.TALLY
MONO ON/OFF
GAMMA SELECT
WFM ON/OFF
Description
continuously at all times.
three seconds.
The menu is displayed in the center.
The menu is displayed in the center.
bottom left.
bottom right.
The settings are displayed in the center.
Description
For allocating particular
functions to particular pins
when remote control
operations are to
performed using the GPI
signals. For details, refer to
"REMOTE specifications"
(page 22).
be
19