Table of Contents
Advertisement
Quick Links
Network Camera
User's Guide
Before operating the unit, please read this manual thoroughly
and retain it for future reference.
Software Version 3.0
SNC-VB635/VB630/VB600/VB600B/VB632D/VB640/VB642D
SNC-VM630/VM600/VM600B/VM631/VM601/VM601B/
VM632R/VM602R/VM641/VM642R
SNC-EB630/EB630B/EB600/EB600B/EB632R/EB602R/
EB640/EB642R
SNC-EM630/EM600/EM631/EM601/EM632R/EM632RC/
EM602R/EM602RC/EM641/EM642R
SNC-XM637/XM636/XM632/XM631
SNC-CX600W/CX600
© 2012 Sony Corporation
D-017-100-11 (1)
Advertisement
Table of Contents
Related Manuals for Sony SNC-VB632D
Summary of Contents for Sony SNC-VB632D
- Page 1 D-017-100-11 (1) Network Camera User’s Guide Before operating the unit, please read this manual thoroughly and retain it for future reference. Software Version 3.0 SNC-VB635/VB630/VB600/VB600B/VB632D/VB640/VB642D SNC-VM630/VM600/VM600B/VM631/VM601/VM601B/ VM632R/VM602R/VM641/VM642R SNC-EB630/EB630B/EB600/EB600B/EB632R/EB602R/ EB640/EB642R SNC-EM630/EM600/EM631/EM601/EM632R/EM632RC/ EM602R/EM602RC/EM641/EM642R SNC-XM637/XM636/XM632/XM631 SNC-CX600W/CX600 © 2012 Sony Corporation...
-
Page 2: Table Of Contents
Date & time Tab ..........24 Table of Contents Installation Tab ..........25 Initialize Tab .............26 System log Tab ..........27 Access log Tab ..........27 Overview Service Tab ............28 Features ..............4 Setting the Camera Image and Audio How to Use This User’s Guide ......5 —... - Page 3 VMF settings ............ 59 Face detection Tab — Set the face detection ..62 Network disconnection Tab — Monitoring the connection of a specified IP address ....63 Setting the Action output — Action output Menu ..............64 Execution Condition Tab ........64 Mail Transfer Tab —...
-
Page 4: Overview
• The camera image can be sent by using Wi-Fi. (SNC- Overview CX600W) NOTICE TO USERS © 2012 Sony Corporation. All rights reserved. This Features manual or the software described herein, in whole or in part, may not be reproduced, translated or reduced to •... -
Page 5: How To Use This User's Guide
How to Use This User’s System Requirements Guide The following computer environment is necessary for the computer to display images and the controls of the This User’s Guide explains how to operate the Network camera. Camera from a computer. (August 2017) The User’s Guide is designed to be read on the computer display. -
Page 6: Function Chart
(page 32)* (page 32)** SNC-VB635 Full HD – SNC-VB630 Full HD – – SNC-VB600 – – SNC-VB600B – – – SNC-VB632D Full HD – SNC-VB640 Full HD – – SNC-VB642D Full HD – SNC-VM630 Full HD – – SNC-VM600 –... - Page 7 High Sensor Alarm Edge Audio Serial Maximum framerate input output Storage (page 33) Illuminator control I/F Model name image size mode (page 55) (page 67) (page 67) (page 35) (page 55) (page 32)* (page 32)** SNC-CX600 – – – – –...
-
Page 8: Accessing The Camera Using The Web Browser
The live viewer window appears (in SSL Accessing the Camera communication). Using the Web Browser After the IP address has been assigned to the camera, check that you can actually access the camera using the Web browser installed on your computer. Start the Web browser on the computer and type the IP address of the camera in the URL address bar. - Page 9 Tips • The software is optimized for Internet Explorer using medium font. • In case a part of the image cannot fit the display, configure the display setting (magnification percentage) to 100%. If you use a display with high pixel density, the magnification percentage may be changed automatically.
-
Page 10: Basic Configuration By The Administrator
Basic Configuration by the Administrator You can monitor the camera image by logging in with the initial conditions set for this network camera. You can also set various functions according to the installing position, network conditions or purpose of the camera. We recommend you configure the following items before monitoring images from the camera. -
Page 11: Precautions For Preventing Access To The Camera By An Unintended Third Party
Set the user name and password of the Precautions for administrator of the camera. For details, refer to “Setting the security — User tab Preventing Access to on the Security menu” in the Administrator menu on page 45. the Camera by an Check the Referer check checkbox. -
Page 12: Operating The Camera
Operating the Camera Administrator and User This network camera identifies those who log in as the Administrator or User. This section explains how to monitor the image from the The Administrator can use all the functions of this camera using your Web browser. network camera, including camera settings. -
Page 13: Logging In To System
Plug-in free viewer Logging in to System This viewer enables a browser other than Internet Explorer to display images. Notes Logging in as a user • If Automatic configuration is enabled in the Local Area Network (LAN) Settings of Internet Explorer, Start the Web browser on your computer and type the camera image may not be displayed. -
Page 14: Configuration Of Live Viewer
Control panel section Configuration of Live You can drag the panels to the monitor screen and Viewer configure them. To return to the control panel, drag the panel and This section explains the functions of the parts and configure the control panel. controls of the live viewer. - Page 15 Capture Camera control panel Click to capture a still image shot by the camera and to store it in the computer. Click to open the folder to be saved. Note When protection mode (Windows > Control panel > Internet options > Security property) is enabled, still images cannot be captured.
-
Page 16: Monitor Image
Monitor screen Monitor image There are two modes for on-screen pan/tilt/zoom operation using a mouse: Area zoom mode and Vector dragging mode. A control bar is displayed on the screen. In the Area zoom mode, click to adjust the camera direction to the center of the image. -
Page 17: Controlling Via The Control Panel (Operation Common To Area Zoom Mode And Vector Dragging Mode)
There are three modes of camera operation: Area zoom Controlling via the control panel mode, Vector dragging mode and PTZ Control bar. (Operation common to Area zoom You can control pan/tilt and zoom in either mode. The available functions for the camera operation modes mode and Vector dragging mode) vary according to the live viewer display. -
Page 18: Panning, Tilting And Zooming By Specifying The Area (Area Zoom Mode Only)
Panning, tilting and zooming by Using pan/tilt/zoom operations with specifying the area (Area zoom the displayed control bar (PTZ mode only) Control bar only) Click and hold the left button of the mouse on the monitor image, and drag the mouse diagonally to draw a red frame around the portion you want to enlarge. -
Page 19: Switching Transmission Mode
Note Switching Transmission When connecting via a proxy server, neither Unicast nor Mode Multicast can be selected. You can change the transmission mode for video/audio data. This function can be used when the video codec mode is set to H.264 and the ActiveX viewer in the live viewer is used. -
Page 20: Playback Viewer
Select Fit to display images in full size with fixed aspect Playback viewer ratio. Search panel Supported models: SNC-VB635/VB630/VB600/ VB600B/VB632D/VB640/VB642D/VM630/VM600/ VM600B/VM631/VM601/VM601B/VM632R/ VM602R/VM641/VM642R/EB640/EB642R/EM641/ EM642R/XM637/XM636/XM632/XM631/CX600W/ CX600 You can play, save or delete the movies recorded in the memory card. This function is available only in the following users. •... - Page 21 Go to the next search result Specify the recorded date and time from which the Displays the next search results. movie will start playback. Go to the previous search result Previous record Displays the previous search results. Jump to the previous movie. Save recorded movie Stop button Click this button to stop a movie playing.
-
Page 22: Monitor Image
Monitor image Play the selected movie from the search results list. Playback viewer... -
Page 23: Administrating The Camera
Select the required tab above the menu, and set each Administrating the Camera setting option in the tab. Example: “Date & time” tab of “System” menu This section explains how to set the functions of the camera by the Administrator. For details about monitoring the camera image, see “Operating the Camera”... -
Page 24: Configuring The System - System Menu
Video Configuring the System Displays the Video menu for setting the camera image. (“Setting the Camera Image and Audio — Video / Audio — System Menu Menu Setting the Camera Image — Video Menu” on page 28) When you click System in the Administrator menu, the Network... -
Page 25: Installation Tab
You can select the format between yyyy-mm-dd The name of the time zone is CentralStandardTime and hh:mm:ss (year-month-day hour:minutes:seconds), the time difference is 6 hours. The name of the summer mm-dd-yyyy hh:mm:ss (month-day-year time is DaylightTime, and the summer time offset from hour:minutes:seconds), and dd-mm-yyyy hh:mm:ss the time difference is 1 hour, starting from the second (day-month-year hour:minutes:seconds). -
Page 26: Initialize Tab
Select On/Off according to the type of installation, such Initialize Tab as on a ceiling, or on a rack, etc. Note When the Eflip setting is changed, the settings in the Video codec tab of the Video / Audio menu or the Video menu are initialized. -
Page 27: System Log Tab
– superimpose logo camera in Log size. Log information can be saved as a file by clicking Focus refresh Download of Download as file. Supported models: SNC-VB632D/VB642D/VM630/ VM600/VM600B/VM631/VM601/VM601B/ Access log Tab VM632R/VM602R/VM641/VM642R/EB632R/ The access record of the camera is displayed. -
Page 28: Service Tab
Use this menu to set the functions of the camera. The Video / Audio menu consists of the following tabs: SNC-VB635/VB630/VB600/VB640/EB640/VB600B: Picture, Focus, Video codec, Audio, Superimpose, Day/Night, Privacy masking and Streaming. SNC-VB632D/VM630/VM600/VM600B/VM631/ VM601/VM601B/VM632R/VM602R/VB642D/ EB642R/VM641/EM641/VM642R/EM642R: Picture, Focus / Zoom, Video codec, Audio, Superimpose, Day/Night, Privacy masking and Streaming. -
Page 29: Picture Tab
Exposure Picture Tab Adjust the settings of exposure. Wide dynamic range (View-DR) Unsupported models: SNC-CX600W/CX600 In high-contrast scenes such as against a back light, this function reduces overexposure and underexposure. Select the checkbox to turn on the Wide dynamic range (View-DR) function. - Page 30 Exposure compensation Fluorescent lamp: Sets a white balance suitable for Select the exposure correction value from the list box to photography under three-band fluorescent lighting adjust the target brightness for the automatic exposure with a neutral white color. setting. A larger value brightens the image, and a smaller Mercury lamp: Sets a white balance suitable for value darkens the image.
-
Page 31: Focus Tab - Adjusting The Focus
OK/Cancel Focus / Zoom Tab — Adjusting the See “Buttons common to every menu” on page 23. focus/zoom Display sample: SNC-VM630 Focus Tab — Adjusting the Focus Supported models: SNC-VB635/VB630/VB600/ Supported models: SNC-VB632D/VB642D/VM630/ VB600B/VB640/EB630/EB640/EB600 VM600/VM600B/VM631/VM601/VM601B/ VM632R/VM602R/VM641/VM642R/EB632R/ Preview screen EB642R/EM630/EM600/EM631/EM601/EM632R/ EM602R/EM641/EM642R/EB602R Preview the image and adjust the focus. -
Page 32: Video Codec Tab
• When Wide dynamic range (View-DR) in the Note Picture tab of the Video / Audio menu is set, you Focus will move out of position after the adjustment of cannot select On. (SNC-VB635/VB630/VB632D/ the zoom and zoom position. Perform focus adjustment. VB640/VB642D/VM630/VM631/VM641/VM642R/ EB640/EB642R/EM641/EM642R/VM632R) •... -
Page 33: Audio Tab
I-picture interval Image quality Set the I-picture insertion interval. If you set Image codec to JPEG, or Bit rate Select Time to set in seconds. compression mode to VBR when Image codec is set to Select Frame to set in frames. H.264, the image quality setting will be enabled. -
Page 34: Superimpose Tab
input connector or the built-in microphone. It is Preview screen adjustable from –10 to +10. Preview the image, and adjust the superimposed image. You can move the position of superimposed image Audio codec displayed on the preview screen by drag and drop. Select the codec type for sending audio input from the m microphone input connector or the built-in Image... -
Page 35: Day/Night Tab
Sync with IR Illuminator is set to Off. image size of the image number. Brightness threshold Events displayed Supported models: SNC-VB632D/VB642D/ Displays in the menu when the type is set to Event. VM632R/VM602R/VM642R/EB632R/EB642R/ Select the type of superimpose to be displayed for the EM632R/EM602R/EM642R/EB602R event. -
Page 36: Privacy Masking Tab
Clear Notes Click the button to delete the privacy mask set in • The image goes out of focus while Easy Focus is Position. operating. • The motion detection alarm does not work while Easy Clear all Focus is operating. Click the button to delete all privacy mask. -
Page 37: Streaming Tab
control. When operating multi-transmission at the same Streaming Tab time, a different port number will be used in every transmission based on the port number specified here. Note Specify different numbers for the video port number and the audio port number. RTSP video port number 1, 2, 3 Specify the H.264 video transmission port number used for RTSP unicast streaming. - Page 38 number) are used for video data communication and At the 0 setting, time out of the Keep-Alive command is control. not available. The settings for Image 1, Image 2 and Image 3 apply to Video port number 1, 2 and 3 respectively. OK/Cancel See “Buttons common to every menu”...
-
Page 39: Configuring The Network - Network Menu
IP address Configuring the Network Displays the current IP address. — Network Menu Subnet mask Displays the current subnet mask. When you click Network in the Administrator menu, the Default gateway Network menu appears. Displays the current default gateway. Use this menu to configure the network to connect the camera and the computer. - Page 40 Host name Type the host name of the camera to be transmitted Type the IP-MTU value for the Ethernet port. to the DHCP server. This setting is valid only when To obtain DNS server address Obtain an IP address automatically (DHCP) is selected.
-
Page 41: Wi-Fi Tab
Security Wi-Fi Tab Displays the current setting method as either Display sample: SNC-CX600W authentication or encryption. None Connect to a Wi-Fi router without encryption. Connect to a Wi-Fi router using WEP (Wired Equivalent Privacy). WPA/WPA2 Connect to a Wi-Fi router by performing an authentication which is compliant to WPA/WPA2 (Wi-Fi Protected Access). -
Page 42: Wps Settings
The automatic setting between the Wi-Fi router and Note the camera starts. It takes up to two minutes to The connection may not be possible if you use the router connect. that is not compliant with the Wi-Fi standard (802.11b/ g/n). -
Page 43: Qos Tab
Default gateway Type the IP-MTU value for the Ethernet port. Displays the current default gateway. To obtain DNS server address Primary DNS server automatically Displays the current primary DNS server. Select Obtain DNS server address automatically. The Primary DNS server and Secondary DNS Secondary DNS server server are assigned automatically. -
Page 44: Upnp Tab
IPv4 QoS Move up Increases the priority of the rule. Select a rule from the QoS table to prioritize and click Enable Move Up. Select the checkbox to configure the QoS setting for IPv4. Move Down Decreases the priority of the rule. Rule Select a rule from the QoS table to lower its priority and Used to register, edit and delete QoS. -
Page 45: Setting The Security - Security Menu
Full: The user can operate all functions except deleting Setting the Security the recorded movie in the memory card. Pan/Tilt: In addition to the Light mode, the user can — Security Menu operate pan/tilt/zoom. Light: In addition to the View mode, the user can select the image size of the viewer, select codec and capture When you click Security... -
Page 46: Access Limit Tab
Access limit Tab SSL Tab This allows you to control which computers can have access to the camera. Likewise, when using IPv6, security settings can be configured for each network. Enable Select the checkbox to enable the access limit. Default policy Select the basic policy of the limit from Allow and Deny for the computers specified in the Network address/ Subnet 1 to Network address/Subnet 10 menus below. - Page 47 • Reload the window when you change the SSL setting. window from the browser. In this case, reload the Press the F5 key on the keyboard to reload. window. Press the F5 key on the keyboard to reload. Common setting SSL server authentication SSL function Certificate options...
- Page 48 Self-signed certificate generation Private key password A self-signed certificate can be generated in the camera Type the password for the private key information to be used when Use a self-signed certificate (For test included in the certificate using up to 50 characters. This use) is selected from Certificate options.
-
Page 49: How To Install The Ca Certificate
Click the OK button appearing on the dialog. How to install the CA certificate The selected file will be imported to the camera. The camera may not be connected because the browser (Internet Explorer) does not display whether the Note certificate will be accepted or not due to the type of Import process will be invalid if the selected file is not a certificate. -
Page 50: To Remove An Installed Ca Certificate
Click Next. To remove an installed CA certificate In Internet Explorer, click in the order Tools, Internet options, Content tab and Certificates. The Certificates dialog appears. Select Automatically selects the certificate store based on the type of certificate and click Next. Completing the Certificate Import Wizard appears. -
Page 51: To Import The Personal Certificate
Select Local Computer as the computer 802.1X Tab administrated in this Snap-in, then click Finish. The items for administrating Certificates appears in the Console Route window. Confirm the relevant certificate, then remove it. To import the personal certificate To use client authentication, follow the steps below to import the personal certificate. -
Page 52: System Configuration Of 802.1X Network
Notes Note • To use the 802.1X authentication function, you need This camera supports EAP mode in which the supplicant knowledge of the 802.1X authentication and digital and the server authenticate using the certificate. This certificate. To establish an 802.1X network, you need mode requires a CA to issue the certificate. -
Page 53: Referer Check Tab
Note Note Cancel The import process becomes invalid if the selected file is Click at the bottom of the screen if you want to not a client certificate or the imported client certificate is cancel changing the private key password after clicking not allowed. -
Page 54: Setting The Ptz Control - Ptz Control Menu
Setting the PTZ control Select the registered numbers of the Exception list. — PTZ control Menu Host name Type the host name or IP address of the PC that supplies When you click PTZ control in the Administrator menu, the web page you want to register on the Exception list. the PTZ control menu appears. -
Page 55: Serial Tab
Press the Set button. Setting the Sensor input/ Note Camera tampering The shooting range memorized in the Home position setting is displayed after turning on the power. detection/Motion detection OK/Cancel See “Buttons common to every menu” on page 23. — Action input Menu Serial Tab Action input When you click... -
Page 56: Event Condition Tab
Event condition Tab Note You cannot set more than two functions for Presence sensor, Camera tampering detection or Network disconnection in the same event condition. Interval Specify the interval time used when condition is set to and, then. In the case the condition is set as 1 and 2, the system sounds an alarm when either 1 or 2 happens, and the other happens within the specified interval. -
Page 57: Camera Tampering Detection Tab - Set The Camera Tampering Detection
• Set Image size1 in the Video codec tab of the Video / VB640/EB630/EB640/EB600 Audio menu or Video menu to the maximum rate. ** Focus/zoom: SNC-VB632D/VB642D/VM630/ • Deselect the checkbox of Image 1 in the PTZ control VM600/VM600B/VM631/VM601/VM601B/ tab of the PTZ control menu. -
Page 58: Setting Items For Motion Detection
Removed object Note When a moving object has been removed from the The frames shown on the monitor screen are not designated area, an alarm sounds. displayed on the image files sent or recorded with motion detection. Notes • Before actual use, perform an operation test and Configuring the detection area confirm that the motion detection function works The following procedure is used to configure the motion... -
Page 59: Vmf Settings
Delete vertex Detection size Specify the minimum detection size and maximum Clicking this button will change the cursor to a detection size for motion detection. To specify the button. In that state, when you click on a part of the detection size, you can either enter values or drag the vertex of the area, the vertex added to that point is vertexes of the area. - Page 60 Time until left/removed object is detected Passing Enter the time you want to elapse before the alarm is triggered. This setting is available only when the filter type is set to Left object or Removed object. Filter settings Settings for each filter can be edited here. The inspection line and active window are set to default values.
- Page 61 Left object Trigger size Specify the minimum trigger size and maximum trigger size of motion. To specify the size, you can either enter values or drag the vertexes of the area. This criterion is for whether a moving object has been left in the trigger area.
-
Page 62: Face Detection Tab - Set The Face Detection
Trigger speed VMF status indicator of Matching decision Specify the minimum and maximum speeds to be detected. The indicator is on when the set filter type conditions are met. Full-screen display button Click to display the ActiveX area in full screen. Clicking again will show the normal display. -
Page 63: Network Disconnection Tab - Monitoring The Connection Of A Specified Ip Address
– Deselect the checkbox of Image 1 in the PTZ Network disconnection Tab control tab of the PTZ control menu. — Monitoring the connection of a – Deselect the checkbox of Stabilizer in the Installation tab of the System menu. specified IP address •... -
Page 64: Setting The Action Output - Action Output Menu
White LED: Set the White LED lighting condition. notification and FTP still image sending. Only the Presence Sensor (SNC-CX600W/CX600) SNC-EB630/EB630B/EB600/EB600B/EB632R/ and the Motion detection (SNC-VB632D/VB642D) EB602R/EM630/EM600/EM631/EM601/ can be selected. The White LED lights up when it is EM632R/EM602R: Execution Condition, Mail dark. - Page 65 SMTP Server Type the POP (receiving mail) server name using up to 64 characters, or type the IP address of the POP server. This setting is necessary when the SMTP server that Notes sends e-mails performs authentication using the POP •...
- Page 66 • When VMF detects an alarm: (VMF) Image file name • When the Network disconnection is detected Type the file name of the image attached to the e-mail (Disconnected) using up to 10 alphanumeric characters, – (hyphen) and • When the Face detection detects an alarm: (Face _ (under score).
-
Page 67: Alarm Output Tab - Setting The Alarm Output
Alarm output Tab — Setting the Edge Storage Tab — Setting the Alarm output Edge Storage movie and still image function You can perform setting in this menu to control the alarm output of the I/O port on the rear of the camera linked to alarm detection function. - Page 68 Overwrite is selected when the number of records Edge Storage still image reaches 4000, the unit will begin to overwrite old records in ascending chronological order. Recording data • Overwrite is not available for a memory card of less You can refer to still image files recorded in the memory than 4 GB.
-
Page 69: Voice Alert Tab
Edge Storage movie Voice alert Tab Recording status Display the current recording status. The recording status will not be updated until the screen is refreshed. Use the Start Recording and Stop Recording button to start or stop the recording manually. Note When recording manually, do not set Edge Storage movie in the Execution Condition tab of the Action... -
Page 70: Http Alarm Notification Tab
Notes Type the recipient of the alarm. • If voice alert is actively linked with a different alarm type while another voice alert is occurring, the first Test voice alert is cancelled and the second one is output. If you click Execute, the alarm will be notified •... - Page 71 Password Set the details of the video codec mode in the Video / Type the password for the FTP server using up to 64 Audio menu or the Video codec tab in the Video menu. characters. Remote path Passive mode Type the path where the files will be sent using up to 64 Set whether to use the passive mode of the FTP server characters.
-
Page 72: White Led Tab
Select the White LED lighting time from 5 seconds to If you click Clear, the suffix of the Sequence number 30 minutes. returns 1. Supported model: SNC-VB632D/VB642D Select the White LED lighting time from 20 seconds to Send 30 minutes. -
Page 73: Setting The Schedule - Schedule Menu
(Periodical), Day/Night, Voice alert, HTTP alarm notification , FTP still image sending (Event) and FTP still image sending (Periodical). SNC-VB632D/VB642D: Mail Transfer (Event), Mail Transfer (Periodical), Alarm output (Event), Alarm output (Timer), Edge Storage movie, Edge Storage still image (Event), Edge Storage still... - Page 74 SNC-CX600W/CX600: Mail Transfer (Event), Mail Transfer (Periodical) , Edge Storage movie, Edge Storage still image (Event), Edge Storage still image (Periodical), Voice alert, White LED, HTTP alarm notification, FTP still image sending (Event) and FTP still image sending (Periodical). Action Displays an action name to set the schedule.
-
Page 75: Glossary
DNS server Others Acronym for Domain Name System server. As an IP address required for connecting to the device on an IP network is numerical and difficult to remember, the Domain Name System was established. A domain name Glossary is alphabetic and is easier to remember. When a client computer uses a domain name to connect to another computer, it asks a DNS server to translate the name into ActiveX control... - Page 76 Network address Subnet mask The portion that identifies the local network (subnet) in 32-bit stream used to distinguish the subnet address an IP address. from an IP address. Network bandwidth Bit rate that can be used for networking. Acronym for Transmission Control Protocol. A standard protocol used for Internet connection.
-
Page 77: Index
Clear..........36 Execution Condition Tab....64 Index Clear all.......... 36 Exposure......... 29 Client certificate......52 Codec ..........75 Color ..........36 Numerics Face detection Tab......62 Color or monochrome selectable ... 72 Factory default ....... 26 802.1X Tab........51 Common setting ... 40, 47, 52, 68 File .......... - Page 78 Picture mode........29 Sharpness........76 Picture Tab........29 Signal..........41 JPEG..........75 Playback viewer .......14, 20 SMTP Server ......65, 76 Plug-in free viewer ....13, 16 SMTP server name ......65 POP server name ......65 Software version......24 Language ........14 Position........34, 36 Solid PTZ ........76 Left object ........57 Primary DNS server ....43, 76 Solid PTZ function ......16 License notice.........14...
- Page 79 Video Menu........28 View angle Tab....... 54 View panel ....... 14, 20 View size ........14 Viewer authentication ....45 Viewer mode ......12, 45 VMD settings ......... 58 VMF..........57 VMF settings........59 Voice alert ........69 Voice alert Tab ....... 69 Volume ...........
- Page 80 Sony Corporation...