Table of Contents
Advertisement
If the status LED doesn't light
green, check the polarity of
the batteries. If you see any
other flashing signal from the
LED, refer to the chart on page
29 to identify the code.
Use the Right Batteries
Your transmitter uses AA
batteries. Use new alkaline
batteries (part #2914). Do
not use rechargeable AA
batteries to power the TQi
transmitter, as they will not
provide sufficient voltage
for optimum transmitter
performance.
Caution: Discontinue running
your model at the first sign of
weak batteries (flashing red
light on the transmitter) to
avoid losing control.
2-4
2-4
12 • MAXX
TRAXXAS TQ
RADIO SYSTEM
i
INSTALLING TRANSMITTER BATTERIES
Your TQi transmitter uses 4 AA batteries. The battery
compartment is located in the base of the transmitter.
1. Remove the battery compartment door by pressing the tab
and sliding the door open.
2. Install the batteries in the correct orientation as indicated in
the battery compartment.
3. Reinstall the battery door and snap it closed.
4. Turn on the transmitter and check the status indicator for a
solid green light.
If the status LED flashes red, the transmitter
batteries may be weak, discharged or
possibly installed incorrectly. Replace with
new batteries. The power indicator light
does not indicate the charge level of the
battery pack installed in the model. Refer to
the Troubleshooting section on page 29 for more information
on the transmitter Status LED codes.
SELECTING BATTERIES FOR YOUR MODEL
Your model does not include a battery or charger. One Lithium Polymer
(LiPo) battery equipped with the Traxxas High Current Connector is
required.
Do not use a Nickle Metal Hydride (NiMH) battery.
Power Cell iD batteries are strongly recommended for maximum
performance and safer charging. The following chart lists available
Power Cell iD LiPo batteries for your model:
LiPo Batteries with iD
2872X
5000mAh 11.1v 3-Cell (3s) 25C LiPo Battery*
2857X
6400mAh 11.1v 3-Cell (3s) 25C LiPo Battery**
2889X
5000mAh 14.8v 4-Cell (4s) 25C LiPo Battery**
2890X
6700mAh 14.8v 4-Cell (4s) 25C LiPo Battery
*Requires additional battery pack spacers for proper fitment (part #8919R, sold separately).
**Requires installation of the included battery pack spacers for proper fitment.
WARNING: FIRE HAZARD!
Users of Lithium Polymer (LiPo) batteries must read the
Warnings and Precautions beginning on page 4. You
MUST use a LiPo balance charger for LiPo batteries or battery
damage with the potential for fire will result.
DO NOT use Nickel Metal Hydride
(NiMH) batteries with this model. The
batteries will become extremely hot
and damage or injury could occur.
SELECTING A CHARGER FOR YOUR MODEL
Make certain you choose the correct type of charger for the batteries you
select. Traxxas recommends you choose a genuine Traxxas EZ-Peak iD
charger for safer charging and maximum battery life and performance.
NiMH
Charger
Part No.
Compatible
EZ-Peak Plus,
2970
YES
4 amps
EZ-Peak Live,
2971
YES
12 amps
EZ-Peak Dual,
2972
YES
8 amps
EZ-Peak Live
2973
YES
Dual, 26 amps
EZ-Peak Plus 4s,
2981
YES
8 amps
Traxxas
LiPo
Battery
Max.
Compatible
iD
Cells
YES
YES
3s
YES
YES
4s
YES
YES
3s
YES
YES
4s
YES
YES
4s
Advertisement
Table of Contents
