Table of Contents
Advertisement
Range-Testing the Radio System
Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation as described in
the previous section.
2. Have a friend hold the model. Make sure hands and clothing are
clear of the wheels and other moving parts on the model.
3. Walk away from the model with the transmitter until you reach the
farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure that
the model responds correctly.
5. Do not attempt to operate the model if there is any problem with
the radio system or any external interference with your radio signal
at your location.
Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the limit
of radio range. At 60mph, a model can cover 88 feet every second! It's
a thrill, but use caution to keep your model in range. If you want to see
your model achieve its maximum speed, it is best to position yourself
in the middle of the truck's running area, not the far end, so you drive
the truck towards and past your position. In addition to maximizing
the radio's range, this technique will keep your model closer to you,
making it easier to see and control. No matter how fast or far you
drive your model, always leave adequate space between you, the
model, and others. Never drive directly toward yourself or others.
TQi Binding Instructions
For proper operation, the transmitter and receiver must be
electronically 'bound.' This has been done for you at the factory.
Should you ever need to re-bind the system or bind to an additional
transmitter or receiver, follow these instructions. Note: The receiver
must be connected to a 4.8-6.0v (nominal) power source for binding
and the transmitter and receiver must be within 5 feet of each other.
1. Press and hold the transmitter's SET button as you switch the
transmitter on. The transmitter's LED will flash red slowly.
Release the SET button.
2. Press and hold the receiver's LINK button as you switch on
the speed control by pressing the EZ-Set button. Release the
LINK button.
3. When the transmitter and receiver's LEDs turn solid green, the
system is bound and ready for use. Confirm that the steering and
throttle operate properly before driving your model.
TRAXXAS TQ
TRAXXAS STABILITY MANAGEMENT (TSM)
Traxxas Stability Management® (TSM)
lets you experience all the extreme
power, speed, and acceleration that
was engineered into your Traxxas
Maxx®. TSM makes your model much easier to control on slippery
surfaces such as loose dirt, smooth concrete, and even ice and snow.
TSM is adjustable to let you optimize
performance for different driving surfaces.
Out of the box, TSM is set for off-road
performance to help you accelerate hard
and fast in the dirt and expertly powerslide
through the turns. The multi-function knob
on your TQi transmitter should be set to the
12:00 position for off-road performance.
When you want to experience all the
top speed Maxx has to offer on paved
surfaces, turn the multi-function knob
counterclockwise to the 9:00 position for
greatly enhanced high speed on-road
stability and control.
TSM never limits your throttle input
or speed.
If you want to experience raw Maxx power
without any help from TSM, turn TSM off by
setting the multi-function knob on the TQi
transmitter to the "0" or off position.
Learn more at Traxxas.com/tsm.
Note: TSM must be completely turned off
while adjusting steering trim.
RADIO SYSTEM
i
HIGH SPEED OFF-ROAD
HIGH SPEED ON-ROAD
TSM OFF
Using Reverse: While driving,
push the throttle trigger
forward to apply brakes.
Once stopped, return the
throttle trigger to neutral.
Push the throttle trigger
forward again to engage
proportional reverse.
Automatic Failsafe
The TQi transmitter and
receiver are equipped with
an automatic failsafe system
that does not require user
programming. In the event
of signal loss or interference,
the throttle will return to
neutral and the steering will
hold its last commanded
position. If failsafe activates
while you are operating your
model, determine the reason
for signal loss and resolve the
problem before operating
your model again.
6,7
6,7
MAXX • 15
Advertisement
Table of Contents
