i-PRO WV-QDC507C Operating Instructions

Operating Instructions
Included Installation Instructions
Dome Cover
WV-QDC507C
Model No.
Before attempting to connect or install this product, please read these instructions carefully and
•
save this manual for future use.
• The external appearance and other parts shown in this manual may differ from the actual
product within the scope that will not interfere with normal use due to improvement of the
product.
Read also the installation guide of the camera to be used.
•
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation.
"<Control No.: C****>" used in these documents should be used to search for information
on our technical information website (https://i-pro.com/global/en/surveillance/training-
support/support/technical-information) and will guide you to the right information.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2023
Preface
This product is the clear type dome cover.
The latest information about the supported cameras <Control No.: C0501>
Specifications
Ambient operating temperature: –50 °C to +60 °C {–58 °F to 140 °F}
Dimensions: 77 mm (W) × 24 mm (H) x 77 mm (D)
{3-1/32 inches (W) x 15/16 inches (H) x 3-1/32 inches (D)}
(Dome diameter 35 mm {1-3/8 inches})
Approx. 20 g {0.04 lbs}
Mass:
Finish: PC resin, Clear
Caution:
• Before attempting to connect or operate this product, please read these instructions carefully.
Precautions
 Do not use this product except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
 Refer installation work or dome cover replacement to the dealer.
Installation work requires technique and experiences.
Failure to observe this may cause fire, electric shock, injury, or damage to the product.
Be sure to consult the dealer.
 The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
When using this product, also read the "Precautions" described in the operating
instructions for the camera to be attached.
Standard Accessories
Operating Instructions (this document) .........1 pc. Waterproof rubber .......................................1 pc.
Installation
Step 1
Turn the
camera
back over.
Cs0223-0
Printed in China
Step 2
Bit
(Camera accessory)
Note:
• Opening the SD cover separates the camera from the enclosure. Note that lifting the
camera may cause the lens to fall off from the camera.
Replace the dome cover
Step 3
Dome plate
Inner dome
★
Dome cover
Waterproof
rubber
• Recommended tightening torque: 1.38 N·m {1.02 lbf·ft}
• Be sure to replace the waterproof rubber with a new
one from the accessories.
Note:
• When installing this unit, remove the protective sheet once, and attach it again to the
surface of the dome cover after installation is complete.
• The lead wire from the IR LED is fixed with a cable tie to the protrusion of the dome plate
(★ portion). Be careful not to break off the lead wire when replacing the dome cover. (In the
illustration above, the lead wires are omitted for convenience of explanation.)
Step 4
Tape
(Locally procured)
Step 5
Note:
• The enclosure and camera are not
fixed. If you raise the camera in this
state, the lens may come off. Work
while the camera is on the stand.
Peel off the tape temporarily
Step 6
securing the SD cover part.
Note:
There are three positioning recesses
(see illustration below) around the
dome cover and inner dome.
Step 7
Recommended tightening torque:
1.38 N·m {1.02 lbf·ft}
Recommended tightening torque:
1.38 N·m {1.02 lbf·ft}
Bit
(Camera accessory)
Turn over
the camera.