Page 1
• Read also the installation guide of the camera to be used. i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation.
Page 2
Caution: • Before attempting to connect or operate this product, please read these instructions carefully. Precaution Do not use this product except with suitable cameras. Failure to observe this may cause a drop resulting in injury or accidents. Refer installation work or dome cover replacement to the dealer. Installation work requires technique and experiences.
Preface This product is the clear type dome cover. <WV-QDC502C> This product is the smoke type dome cover (approx. 45 % of transmittance). <WV-QDC502G> The latest information about the supported cameras <Control No.: C0501> Specifications Ambient operating –50 °C to +60 °C {–58 °F to 140 °F} temperature: Dimensions: ø131 mm ×...
Page 4
The procedure for installing this unit to the network camera varies depending on the model used. Install according to the following compatible models. Type1 Page 5 Type2 Page 10...
Installation Type1 Illustrations onward are the example of replacing the smoked type dome cover. Step 1 Rotate the decorative cover by approximately 10 degrees counterclockwise in topneath view. Step 2 Remove the decorative cover.
Page 6
more than 75 mm Step 3 {2-15/16 inches} Remove the dome cover holding plate (4 pcs.). Caution: • Use the screwdriver (locally procured) with a bit length of 75 mm {2-15/16 inches} or more. • Dispose of the removed dome cover holding plates (4 pcs.) and mounting screws (8 pcs.).
Page 7
Step 4 Remove the dome cover. Be careful to the following when replacing the dome cover: - The waterproof rubber may come off simultaneously. Attach the waterproof rubber to the original position before attaching this product. - It is recommended to check whether the waterproof rubber is deteriorated.
Page 8
more than 75 mm Step 6 {2-15/16 inches} Mounting screw (8 pcs.) (accessory) Tighten the mounting screws (accessory) to attach the dome cover holding plate ② (accessory). ③ ④ Caution: • Use the screwdriver (locally ① procured) with a bit length of Dome cover 75 mm {2-15/16 inches} or more.
Page 9
Step 8 Rotate the decorative cover by approximately 10 degrees clockwise in topneath view. Attach the protection film that was removed in the step 5 to the surface of the dome cover again. After completing the installation, remove the protection film. Step 9 Install the camera by following the instructions in the Installation Guide of the camera.
Page 10
Installation Type2 Step 1 When replacing before installation (camera accessory) When replacing after installation Installed auxiliary wire Resin sheet...
Page 11
Step 2 Note: • The center cover is fixed with 3 hooks. Hook (3 places) Logo ① ③ ② ① Prepare a screwdriver with a small tip (about 5 mm {3/16 inches} wide). ② Insert a screwdriver into the slit at the “A” position of the center cover, lower the screwdriver and lift the center cover upwards.
Page 12
Step 3 • Use the screwdriver (locally procured) with a bit length of 75 mm {2-15/16 inches} or more. Step 4 Replace the dome cover Removed dome cover This product • When replacing the dome cover, install with the protection film attached to this product. Waterproof rubber Be careful to the following when...
Page 13
Step 5 0.3 N·m {0.22 lbf·ft} Hook (3 places) Logo Note: • Make sure that the three hooks on the center cover are completely fixed with a snap sound. Step 6 Attach the enclosure to the camera. Refer to the Installation Guide for how to attach it to the camera.
Page 24
Step 2 メモ: センターカバーは3か所のフックで固定され ています。 フック位置 (3か所) ロゴ位置 ① ③ ② ① 先端の小さな(幅 5 mm程度)マイナスドライバーを用意する。 ② センターカバーの 「A」 位置にあるスリットにドライバー差し込み、 マイナスドライバー を下の方に下げ、センターカバーを持ち上げるようにしてフックを外す。 ③ 「 A」位置のフックが外れたら、ドライバーを差し込んだまま移動させ残りの2か所の フックを同じようにして外す。...