i-PRO WV-QSR505 Operating Instructions

Operating Instructions
Included Installation Instructions
Sunshade
WV-QSR505
Model No.
• Before attempting to connect or install this product, please read these instructions carefully.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation.
"<Control No.: C****>" used in these documents should be used to search for
information on our technical information website (https://i-pro.com/global/en/
surveillance/training-support/support/technical-information) and will guide you to
the right information.
i-PRO Co., Ltd.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
Caution:
• Before attempting to connect or operate this
product, please read these instructions care-
fully.
Preface
This unit is a sunshade to be attached to an
outdoor dome-type camera.
Specifications
Ambient operating temperature: –40 °C to +60 °C {–40 °F to +140 °F}
Dimensions: 194 mm (W) x 153 mm (H) x 83 mm (D)
{7-5/8 inches(W) x 6-1/32 inches(H) x 3-9/32 inches (D)}
Mass: Approx. 120
Finish:
PC resin i-PRO white (WV-QSR505-W)
Precautions
 Do not use this product except with suitable cameras. 
Failure to observe this may cause a drop resulting in injury or accidents.
 Refer installation work to the dealer. 
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
When using this product, also read the "Precautions" described in the operating
instructions for the camera to be attached.
Notice:
• This product is not suitable for use in loca-
tions where children are likely to be present.
• Do not install this product in locations where
ordinary persons can easily reach.
The latest information about the supported
cameras <Control No.:C0501>.
g
{0.24 lbs}
Black (WV-QSR505-B)
Precautions for installation
 In order to prevent injury, the product must be securely mounted to the camera 
according to the Installation Guide of this product.
 Make sure to remove this product if it will no longer be used. 
Standard Accessories
Operating Instructions (this document) ....... 1 pc.
Other items that are needed (not included)
Thin screwdriver ......................................... 1 pc
Installation
Remove the enclosure part from the camera.
Step 1
For removal instructions, please refer to the Installation Guide or preparation section of the
Installation Guide leaflet for each camera.
Check installation direction.
Step 2
• If this product is attached to a camera, it should be installed on a wall only.
• This product can be mounted in four directions on the camera. Determine the posi-
tion to install the product according to the direction of the wiring.
• This product is used to reduce the effect of ambient light on the lower part of the
screen. Therefore, the shadow of this product will appear on the upper part of the
screen.
Wiring direction
avs0822-1092
Printed in China
Remove the two enclosure fixing screws from the enclosure.
Step 3
①
Fasten the unit to the enclosure.
Step 4
Bit (Camera accessories)
③
Bit (Camera accessories) ............................ 1 pc
①
②
① Press the enclosure fixing screws (2 of 4 locations)
from the inside with a thin screwdriver (locally pro-
cured).
② While performing ①, use a screwdriver from the
outside of the enclosure to rotate the enclosure fixing
screw counterclockwise and remove it.
③ Temporarily secure the unit to the enclosure and
rotate the long enclosure fixing screw attached to
this product clockwise to penetrate the enclosure of
the camera.
③
Technical information website
Infrared Illumination effects and reflections
on the screen when using sunshades
<Control No.:C0511>.
For tightening torques, please refer to the camera
Installation Guide or the Installation Guide leaflet.
⇒Back to the camera installation procedure
Wiring direction
Bit (Camera accessories)
②