i-PRO WV-QLR100-W Operating Instructions

Operating Instructions
Included Installation Instructions
Light Rail Mounting Bracket
WV-QLR100-W
Model No.
WV-QLR100-B
• Before attempting to connect or install this product, please read these instructions carefully.
• The external appearance and other parts shown in this manual may differ from the actual product
within the scope that will not interfere with normal use due to improvement of the product.
i-PRO Co., Ltd. assumes no responsibility for injuries or property damage resulting
from failures arising out of improper installation or operation inconsistent with this
documentation or through use of parts other than this product, such as locally
procured parts.
"<Control No.: C****>" used in these documents should be used to search for
information on our technical information website (https://i-pro.com/global/en/
surveillance/training-support/support/technical-information) and will guide you to
the right information.
i-PRO Co., Ltd.
https://www.i-pro.com/
© i-PRO Co., Ltd. 2022
Caution:
• Before attempting to connect or operate this
product, please read these instructions care-
fully.
Precautions
„ Do not use this bracket except with suitable cameras.
Failure to observe this may cause a drop resulting in injury or accidents.
„ Do not install equipment that exceeds the maximum loading weight.
Failure to observe this may cause a drop resulting in injury or accidents.
Be sure to observe the maximum loading weight.
„ Do not install or wire the lighting rail with the power on.
Failure to observe this may cause fire or electric shock.
„ Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product.
Be sure to consult the dealer.
„ The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury or accidents.
Be sure to install the safety wire.
„ The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
„ Install the product securely on the lighting rail in accordance with the installation
instructions.
Failure to observe this may cause injury or accidents.
„ Do not rub the edges of metal parts with your hand.
Failure to observe this may cause injury.
When using this product, also read the "Precautions" described in the operating
instructions for the camera to be attached.
avs0622-1082
Printed in China
Notice:
• This product is not suitable for use in loca-
tions where children are likely to be present.
• Do not install this product in locations where
ordinary persons can easily reach.
• For information about screws and other parts
required for installation, refer to the corre-
sponding section of this document.
Preface
This product is a mounting base for cameras. You can attach this product to the lighting rail and
install the camera. Two colors, white and black, are available, so it can be installed in consideration
of the surrounding landscape.
The latest information about the supported cameras <Control No.:C0501>.
Specifications
Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}
Dimensions: Width: 63.5 mm {2-1/2 inches}
Depth: 32 mm{1-1/4 inches}
Height: 135 mm {5-5/16 inches}(From the ground plane of the
lighting rail to the camera mounting surface)(not including camera
mounting screw)
Mass: Approx. 130
Finish: Aluminum alloy, PA/ABS resin white /black
Max. loading weight: 1 k {0.33 lbs}
g
Precautions for installation
„ In order to prevent injury, the product must be securely mounted to the lighting rail
according to the Installation Guide of this product.
„ This product is designed to be used indoors.
This product is not operable outdoors. Do not expose this product to direct sunlight for hours and
do not install the product near a heater or an air conditioner. Otherwise, it may cause deformation,
discoloration and malfunction. Keep this product away from water and moisture.
„ Make sure to remove this product if it will no longer be used.
Standard Accessories
Operating Instructions (this document) ....... 1 pc.
Screw x3
（M3x9mm {11/32 inches}） （ of them, 1 for spare)
Other items that are needed (not included)
Lighting rails.
3 mm {1/8 inches} hexagon wrench .......... 1 pc.
IMPORTANT
• Use a lighting rail with the dimensions specified in Step 1 Check available lighting rails.
Installation
Refer to the operating instructions of the camera for details on the camera installation
(including the cable connection and adjustment).
Check available lighting rails
Step 1
This product can be mounted on a lighting rail with the following dimensions.
If you are using a lighting rail with different dimensions, please check the dimensions of the mount-
ing portion of this product to see if it can be installed.
Install on a lighting rail that conforms to the standards and specifications specified in your
country/region of use.
33 mm{1-5/16 inches}
17 mm
{21/32 inches}
14 mm
{9/16 inches}
Stopper button
Polarity indication
3 mm
{1/8 inches}
g {0.29 lbs}(Including mounting screws)
13.5 mm{17/32 inches}
19 mm
{3/4 inches}
Stopper button
24.8 mm
{31/32 inches}