Advertisement
WaRninG
improper maintenance can cause injury. Maintain
the restraint only as described in this manual.
important
Metal buckles and speed clips can be damaged by
immersion in liquids or by washing-machine action.
Disinfect and clean only as described in this manual.
important
Disinfectants
and
cleaners
phenolics, or iodines can cause damage. Do not use
products containing these chemicals.
Maintenance Schedule
The restraint requires regular maintenance. Set up and follow a
maintenance schedule. Conduct maintenance as follows:
Inspecting: Inspect the restraint as needed, following the
●
Inspection Checklist below. At minimum, inspect monthly.
Disinfecting: Disinfect the restraint after each use.
●
Cleaning: Clean the restraint as needed.
●
inspection checklist
Are all components present?
●
Is restraint webbing in good condition (no cuts/frayed edges)?
●
Are restraint buckles and speed clips free of visible damage?
●
Do buckles open and close smoothly and properly?
●
Can strap length be adjusted smoothly and properly?
●
Do the speed clips operate properly?
●
If inspection indicates damage or excessive wear, take the restraint
out of service and destroy it.
Disinfecting the Restraint
1.
Remove the restraint from the equipment.
2.
Spray the metal buckles and speed clips with a disinfectant
cleaner, following the disinfectant manufacturer's instructions
for application method and contact time. Do not immerse the
buckles or speed clips in liquid.
3.
Hang the restraint to air-dry if needed. Attach only dry
restraints to the equipment.
cleaning the Restraint
1.
Immerse the restraint webbing in a solution of mild soap and
water. Do not immerse metal buckles or speed clips in the
solution.
Repeatedly dip the webbing in clear water to rinse. Do not
2.
immerse metal buckles or speed clips in liquid.
3.
Hang the restraint to air-dry. Attach only clean, dry restraints
to the equipment.
4
containing
bleach,
Model 436 Speed-Clip Restraints
Model 436-i Restraint (single restraint)
Model
Length
031-4124
5 ft/1524 mm
031-4122
5 ft/1524 mm
031-4125
7 ft/2134 mm
031-4123
7 ft/2134 mm
Model 436 Restraint (set of 4)
Model
Length
031-4120
5 ft/1524 mm
031-4118
5 ft/1524 mm
031-4121
7 ft/2134 mm
031-4119
7 ft/2134 mm
Ferno technical Support
Customer service and product support are important aspects of
each Ferno product. For technical support questions:
Telephone (Toll-free)
Telephone
Email
Ferno customer Relations
canaDa anD the U.S.a.
Telephone (Toll-free)
Telephone
Fax (Toll-free)
Fax
Internet
aLL otheR LocationS
For assistance or information, contact your Ferno distributor. If you
do not have a Ferno distributor, contact Ferno Customer Relations:
Telephone
Fax
Internet
Limited Warranty Statement
The products sold by Ferno are covered by a limited warranty,
which is printed on the invoice you received when you purchased
the product. Please refer to the warranty terms as printed on your
invoice. The complete terms and conditions of the limited warranty,
and the limitations of liability and disclaimers, are also available upon
request by calling Ferno at 1.800.733.3766 or 1.937.382.1451.
© Ferno-Washington, Inc 234-3541-00 September 2013
Buckle
Plastic
Metal
Plastic
Metal
Buckle
Plastic
Metal
Plastic
Metal
1.800.733.3766 ext. 1010
1.937.382.1451 ext. 1010
quality.products@ferno.com
1.877.733.0911
1.937.382.1451
1.888.388.1349
1.937.382.1191
www.ferno.com
+1.937.382.1451
+1.937.382.6569
www.ferno.com
Advertisement
