Table of Contents
Advertisement
Quick Links
No: 31672 – 10/22 rev. 4
Catalog Numbers • Les Numéros de Catalogue • Los Números de Catálogo:
LMSW-610-S, LMSW-611-S, LMSW-622-S, LMSW-641-S, LMSW-632-S
Country of Origin: Made in China • Pays d'origine: Fabriqué en Chine • País de origen: Hecho en China
LMSW-610-S
LMSW-611-S
Once paired to a wireless room controller or wireless bridge,
adjustment via the DLM Configuration App or LMCS-100 may
be required to meet the local energy code where installed.
The DLM Wireless Slim Switches are wireless battery powered wall
switches intended for operation with wireless room controllers or
wireless bridges in hybrid rooms.
Do not apply cleaning solvent directly onto unit. Apply cleaning solvent onto
a cloth, then wipe the unit to clean it.
NOTE: Installation shall be in accordance with all applicable
regulations, local, and NEC codes
Status/Battery
Life LED
Tap: Fade to OFF
Press & Hold: Ramp Down
Double Tap: Immediate OFF
with no fade
LMSW-622-S
LMSW-641-S
BUTTONS AND INDICATORS
Button(s) can be set
to toggle on/off or
to function as a
scene switch
Tap when load OFF: Turn ON to last level
Tap when load ON: Go to full bright
Press & Hold: Ramp Up
Double Tap: Immediate ONwith no fade
Configuration Button
(Right side of Legrand badge)
Wattstopper
DLM Wireless Slim Switches with IPv6/Bluetooth
Installation Instructions • Instructions d'Installation • Instrucciones de Instalación
Power Supply ..........Battery powered, CR2032 Battery, 3VDC
Connection to DLM Network
..................Wireless via LMRC-6xx/LMPL-6xx load controllers
..............................................................................or LMBC-650
Wireless Radio ................. Single, Concurrent 802.15.4 and
Wireless Communication
LMSW-632-S
Wireless Encryption ................... AES-128 bit symmetric key
Environment .........................................For Indoor Use Only
Compliance/Regulatory
LED Behavior
Red/Green/Blue Flash
Green, 1 Blink
Green, Repeating Blink
Red, 1 Blink
Red, Repeating Blink
White
Green, On for 3 seconds Config button soft-lock activated
Green, Blinks 3 times
®
®
Low Energy Technology
SPECIFICATIONS
............................. Bluetooth Low Energy, 2.4GHz
IPv6 Mesh (6LoWPAN) Range .................... up to 60 ft.
Bluetooth low energy technology Range .... up to 30 ft.
60 ft. max. between LMSW-6xx-S and load controller
or bridge
Operating Temperature ........ 32° to 140°F (0° to 60°C)
Storage Temperature .......... 23° to 140°F (-5° to 60°C)
Relative Humidity .............. 5 to 95% (non condensing)
UL, cUL, FCC, IC
RoHS
Bluetooth certified
Meaning
Unit Boot Up
Config Button Pressed
Push to Pair Mode
In normal operation, if any button
press, indicates low battery
Also blinks if Config button is
pressed 10 times (to reset unit)
Push n' Learn Mode
Button or Rocker pressed during
normal operation
Config button soft-lock deactivated
Advertisement
Table of Contents
Related Manuals for LEGRAND Wattstopper LMSW-632-S
Summary of Contents for LEGRAND Wattstopper LMSW-632-S
- Page 1 Double Tap: Immediate OFF with no fade Configuration Button Red, Repeating Blink Push n’ Learn Mode (Right side of Legrand badge) White Button or Rocker pressed during normal operation Green, On for 3 seconds Config button soft-lock activated Green, Blinks 3 times...
-
Page 2: Installing The Switch
Wall box mount: Wall box mounting allows for use of any standard decora-sized wall plate (not included). If using any plate other than a Legrand radiant wall plate, the top and bottom radiant mount wings should be removed from the switch. - Page 3 WIRELESS ROOM CONNECTION LMBR-650 For networking and Distance Recommendations: managing rooms, IPv6 Mesh for 30’ max between LMSW-6xx-S and mobile device floors, and building networking of DLM (not needed for 60’ max. between LMSW-6xx-S and room rooms and devices stand-alone rooms) controller or bridge over 6LoWPAN 10’...
- Page 4 1. Enter PtP mode on the room controller. Press the Config button three times (within three seconds) until the LED on the room controller flashes green. 2. Enter PtP mode on the LMSW-6xx-S. Press the Configuration button (on the right side of the Legrand badge) three times. As with the room controller, the LED on the switch will flash green.
- Page 5 1. Enter PtP mode on the LMBC-650. Using a pointed tool, press the Config button three times (within three seconds) until the LED on the LMBC-650 flashes green. 2. Enter PtP mode on the LMSW-6xx-S. Press the Config button (right side of Legrand badge) three times. As with the wireless bridge, the LED on the switch will flash green.
- Page 6 LMSW-610-S Input Wireless PnG Binding Default Tap Default Hold Ideal Application: Button All Lighting Loads Toggle On/Off Toggle Dim* • Single-zone • Single scene recall • Toggle control LMSW-611-S Input Wireless PnG Binding Default Tap Default Hold Ideal Application: Button All Lighting Loads Toggle On/Off Toggle Dim*...
-
Page 7: Replacing The Battery
2. Locate the prying location at the bottom left corner of the switch frame (slightly below the Legrand badge), as shown. Insert a small prying tool and pull the corner of the switch frame away from the wall. The switch will detach from the mounting plate with frame and buttons intact. -
Page 8: Fcc Regulatory Statements
No. 31672 – 10/22 rev. 4 © Copyright 2022 Legrand All Rights Reserved. 800.879.8585 © Copyright 2022 Tous droits réservés Legrand. www.legrand.us/wattstopper © Copyright 2022 Legrand Todos los derechos reservados.