Fein C915-125BL Series Manual page 31

OBJ_BUCH-0000000474-001.book Page 31 Thursday, January 26, 2023 11:41 AM
Mounting the safety cover (see page 9)
– Slide the safety cover over the wheel guard.
– Pay attention that the two engaging hooks are fully
engaged.
Features
Securing cable
For working aloft, FEIN offers suitable securing cables
for the product as accessories (see page 17).
Do not exceed the maximum load
WARNING
specified on the securing cable.
Otherwise, serious or fatal injuries may result.
Observe the safety and operating instructions enclosed
with the securing cable.
Connect the securing cable to the intended fastening
point of the power tool only as shown (see page 6).
The soft start is used to reduce torque reaction forces
when switching on and running up the power tool to
the no-load speed.
The restarting protection prevents the power tool from
automatically restarting if the power supply is inter-
rupted during operation. In this case, switch off the
power tool, check the power supply and then switch
the power tool on again.
The blocking monitor reduces the risk of motor damage
and the risk of accidents when an application tool
blocks. In this case, the power tool switches off auto-
matically. Afterwards, set the switch to the off position,
remove the power tool from the workpiece and check
the application tool for damage. Afterwards, switch the
power tool on again.
The electronic overload protection reduces the risk of
motor damage if the power tool is overloaded. In this
case, the power tool switches off automatically. After-
wards, set the switch to the off position, remove the
power tool from the workpiece and check the applica-
tion tool for damage. Afterwards, switch the power
tool on again.
The electronic speed preselection enables the speed to
be adapted to the respective application and the respec-
tive application tool.
The kickback monitoring reduces the risk of unex-
pected kickback of the power tool. In this case, the
power tool switches off automatically. Afterwards, set
the switch to the off position, remove the power tool
from the workpiece and check the application tool for
damage. Afterwards, switch the power tool on again.
The power tool is equipped with a brake system for
braking down the application tool. This reduces the risk
of accidents.
Only for CG15-125BLP (**), CG15-150BLP (**),
CG15-125BLP Inox (**):
The dead man's switch is a non-lockable switch. The
dead man's switch must be continuously actuated to
keep the power tool in operation.
Meaning of the LED indicator.
When errors occur that are not listed in the fol-
lowing table, please the after-sales service.
Green State Explanation
LED
Lit Opera- Normal condition as soon
tional readi- as plug is connected to
ness mains, also during opera-
tion.
Flashing Thermal Warning against and signal-
overload ling of thermal overload
shut-off. In addition, the
user is warned by a notice-
able drop in speed (power
limitation).
Off Error If the green LED is off, an
error is present, e.g. defec-
tive power cord.
Repair and customer service.
Please observe that power tools may only be
repaired, maintained and inspected by qualified
electricians, as improper maintenance can result in con-
siderable hazards for the user.
When working metal under extreme oper-
ating conditions, it is possible for conductive
dust to settle in the interior of the power
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via
the ventilation slots frequently with dry and oil-free
compressed air.
When working gypsum-containing materials, dust can
settle within the power tool and switch element, which
can harden in connection with humidity. This can
impair the switching mechanism. Blow out the interior
of the power tool via the ventilation slots and the
switch element frequently with dry and oil-free com-
pressed air.
Products that have come into contact with asbestos
may not be sent in for repair. Dispose of products con-
taminated with asbestos according to the applicable
country-specific regulations for such disposal.
en
31