Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Erbauer EHTP22
Summary of Contents for Erbauer EHTP22
- Page 1 Petrol Hedge Trimmer (22.2 cm EHTP22 EAN: 5059340256498 BX220IM/B3 WARNING: Read the instruction handbook thoroughly before using the machine. First time operators should receive practical use instructions of the machine and protective equipment from an experienced operator.
-
Page 2: Table Of Contents
EHTP22 Let’s get started... These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting Started... Safety information Technical specifications Your equipment Before start Quick start more detail... Equipment functions Operation... -
Page 3: Safety Information
Safety information EHTP22 Safety warnings IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE > This equipment is not intended for use by children and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. >... - Page 4 Safety information EHTP22 > Use extra care when handling fuels. Fuel is flammable and the vapours are explosive. The following points should be observed. • Use only an approved container. • Never remove the fuel cap or add fuel with the power source running. Allow engine and exhaust components to cool down before refuelling.
- Page 5 Safety information EHTP22 > Always be aware of your surroundings and stay alert for possible hazards of which you might not be aware due to the noise of the hedge trimmer. > Keep all parts of the body away from the cutting blade. A moment of inattention while operating the hedge trimmer may result in serious personal injury.
- Page 6 Safety information EHTP22 > Use caution when handling fuel. To avoid any accidental fires, move the equipment at least 3 metres from the fuelling point before starting the engine. > Do not operate the equipment if it is leaking fuel.
- Page 7 Safety information EHTP22 Emergency Familiarise yourself with the use of this equipment by means of this instruction manual. Memorise the safety directions and follow them to the letter. This will help to prevent risks and hazards. > Always be alert when using this equipment, so that you can recognise and handle risks early.
- Page 8 Safety information EHTP22 Symbols On the equipment, the rating label and within these instructions you will find among others the following symbols and abbreviations. Familiarise yourself with them to reduce hazards like personal injuries and damage to property. Kilowatt Litre...
- Page 9 Safety information EHTP22 Open flames in the work area, around the equipment and in the vicinity of flammable materials are prohibited! Do not smoke in the work area, around the equipment and in the vicinity of flammable materials! Risk of fire/flammable materials.
- Page 10 Safety information EHTP22 Pull the recoil starter handle 3 times. Pull the recoil starter handle until the engine starts. Guaranteed sound power level value in dB. The equipment complies with the applicable European directives and an evaluation method of conformity for these directives was done.
-
Page 11: Technical Specifications
Technical specifications EHTP22 Technical specifications General Dimensions: > approx. 1270 x 265 x 210 cm > Weight: approx. 5.84 kg > Fuel tank capacity: 440 cm (ml) Petrol type: > Octane rating of at least 90, unleaded, Maximum 10% renewable ethanol (E10 or below) >... - Page 12 Technical specifications EHTP22 Sound emission level > Sound pressure level L 94.2 dB(A) > Uncertainty K: 3.0 dB(A) > Measured sound power level L 104.3 dB(A) > Uncertainty K: 3.0 dB(A) > Guaranteed sound power level L 107 dB(A) Vibration emission level Hand-arm vibration a >...
-
Page 13: Your Equipment
Your equipment EHTP22... -
Page 14: Before You Start
Your equipment / Before you start EHTP22 1. Rear handle 13. Locking screw 2. Throttle control lock-out 14. Primer 3. Throttle control 15. Fuel tank cap 4. Stop switch 16. Fuel tank 5. Recoil starter handle 17. Rear handle adjustment lever 6. - Page 15 Before you start EHTP22 Set up Removing the cutting device transport guard CAUTION! Risk of cuts! Cutter blades (9) are very sharp. Wear protective gloves when handling cutter blades (9). Remove the cutting device transport guard (23) carefully from the cutting device (8) (Fig. 1).
- Page 16 Before you start EHTP22 2. Release the rear handle adjustment lever (17) to lock the position in place (Fig. 6). NOTE: The rear handle (1) can only be locked at 3 positions. Make sure it snaps securely into place before operating the equipment.
- Page 17 Before you start EHTP22 Filling up fuel and oil WARNING! This equipment is not supplied with petrol-oil mixture in the engine! Before operating this equipment it is essential to fill it with petrol-oil mixture! This equipment is equipped with a 2-stroke engine. The fuel and oil tank are combined and it is essential to fill a fuel-oil mixture before operating this equipment.
- Page 18 Before you start EHTP22 100 ml 2.5 ml 200 ml 5 ml 40:1 300 ml 7.5 ml 400 ml 10 ml 4. Unscrew and remove the fuel tank cap (15) (Fig. 7). 5. Fill the fuel into the fuel tank (16). Leave approximately 5 mm of space between the top of the fuel and the inside edge of the tank to allow for expansion.
- Page 19 Before you start EHTP22 Operating controls Choke lever Recoil starter handle Primer Stop switch Throttle Throttle control control lock-out lock-out Rear handle adjustment lever Throttle control...
-
Page 20: Quick Start
Quick start EHTP22 Preparation Assemble Adjust Add fuel and oil mixture Starting (Cold engine) Press primer Set the choke to Pull recoil starter Set the choke to 7 times CLOSE handle OPEN 3 times (If engine already started, skip step 5) - Page 21 Quick start EHTP22 Starting (Warm engine) Set the choke to Pull recoil starter Squeeze throttle Operate OPEN handle until the control lock-out engine starts and throttle control and release them Stopping Push the stop switch to Release throttle control and...
-
Page 22: In More Detail
EHTP22 Intended use This petrol hedge trimmer EHTP22 is designated with a maximum power output of 0.85 kW. This equipment intended for trimming hedges, bushes and shrubs with a maximum diameter of 28 mm. Do not use the equipment for any other purpose. - Page 23 Equipment functions EHTP22 Hand barrier > The front hand barrier (7) and rear hand barrier (18) prevent the operator from getting injured by the cutting blades or flying objects (Fig. 9 and 10). Throttle control lock-out The throttle control lock-out (2) prevents unintentional start of the throttle control (3). The throttle control can only be activated if the throttle control lock-out is pressed (Fig.
-
Page 24: Operation
Operation EHTP22 Operation Check before starting: 1. Check the equipment, as well as accessories for damage before each use. Do not use the equipment if it is damaged or shows wear. 2. Double check that the cutting device (8) is properly fixed, tightened and lubricated. - Page 25 Operation EHTP22 Starting the engine DANGER! Risk of fire! > Due to any spilled fuel, the equipment can catch fire. > Wipe any spilled fuel up before starting. > Start the engine a few metres away from the place where you have filled it.
- Page 26 Operation EHTP22 Starting cold engine NOTE: For a cold start, make sure that the rear handle (1) is in the upright position. 1. Place the equipment on a flat and stable surface. The cutting device (8) should not touch ground or any objects.
- Page 27 Operation EHTP22 Starting warm engine 1. Place the equipment on a flat and stable surface. The cutting device (8) should not touch ground or any objects. 2. Ensure the choke lever (11) is set to OPEN position (Fig. 15). 3. Hold the machine securely to the ground with your left hand. Pull the recoil starter handle (5) slowly with your right hand until you feel a definite resistance and then give it a brisk, strong pull.
- Page 28 Operation EHTP22 Trimming tips WARNING! When operating the equipment, always keep the blades away from your body (Fig. 16-19). Body on the opposite Body on the opposite side of the blades side of the blades Body on the opposite Body on the opposite...
- Page 29 Operation EHTP22 NOTE: Always keep the cutting device (8) at an angle of approximately 15° to the cutting surface. > Cut and remove branches exceeding the cutting capacity of this equipment (28 mm) (28 mm) using a proper pruner before operation.
-
Page 30: Care And Maintenance
Operation / Care and maintenance EHTP22 After use 1. Stop the engine, disconnect the spark plug connector and let the engine cool down. 2. Check, clean and store the equipment as described below. WARNING! The cutting device (8) continues to move for some time after the engine has been switched off. - Page 31 Care and maintenance EHTP22 Cleaning NOTE: Do not use chemical, alkaline, abrasive or other aggressive detergents or disinfectants to clean this equipment as they might be harmful to its surfaces. Cleaning the housing > Use a damp, lint-free cloth to clean the housing.
- Page 32 Care and maintenance EHTP22 Maintenance table Inspect and maintain this equipment regularly based on below maintenance table. Keep the equipment in good working condition during maintenance. Part Task Before/after Every 15 hours 15 hours of Every 25 hours each use...
- Page 33 Care and maintenance EHTP22 Air filter Inspect the air filter regularly. Clean or replace it with a new one if necessary. 1. Loose the locking screw (13) on the air filter case (12) (Fig. 25). 2. Remove the air filter and tap it on a stable surface to remove dust. Use compressed air (max.
- Page 34 Care and maintenance EHTP22 Spark plug NOTE: For good performance, the spark plug must be properly gapped and must be free of deposits. Inspect the spark plug every 25 hours or before long-term storage over 30 days. Clean or replace with a new one if necessary.
- Page 35 Care and maintenance EHTP22 Gear box > Lubricate the gear box on the bottom of the equipment every 25 hours or more frequent at heavy use. > Add grease through the lubricator with an lubricating gun until the grease comes out between the gear box and the cutting device (8) (Fig.
- Page 36 Care and maintenance EHTP22 Cutting device Clean the cutting device (8) regularly. Check it for any damage and protect it from corrosion. If necessary take the cutting device (8) to an authorized dealer for sharpening. Carburetor The carburettor has been carefully set at the factory. Adjustment may be necessary if you notice that the engine does not idle (e.g.
- Page 37 Care and maintenance EHTP22 Silencer If it is necessary to replace the silencer, contact an authorised service centre or a similarly qualified person. Inspect the silencer fixing screws regularly. Tighten them if they are loosened. Spare parts/Replacement parts The following parts of this equipment may be replaced by the consumer. Spare parts are available at an authorised dealer or through our customer service.
- Page 38 Care and maintenance EHTP22 Long term storage NOTE: Risk of equipment damage! > If you are not going to use the equipment for a while, remove the fuel from the equipment. This way, you will prevent a gumming-up of the engine and of the grease pump.
-
Page 39: Troubleshooting
Troubleshooting EHTP22 Troubleshooting Suspected malfunctions are often due to causes that the operators can fix themselves. Therefore check the equipment using this section. In most cases, the problem can be solved quickly. WARNING! Only perform the steps described in these instructions! All further... -
Page 40: Recycling And Disposal
Troubleshooting / Recycling and disposal EHTP22 Problem Possible cause Solution Engine does not Air filter is soiled? Clean the air filter. reach Incorrect fuel or incorrect Stop the engine, empty tank, then the maximum mixture? fill up with the correct mixture of speed. -
Page 41: Guarantee
Guarantee EHTP22 Guarantee We take special care to select high quality materials and use manufacturing techniques that allow us to create products incorporating design and durability. This product has a manufacturer’s guarantee of 2 years against manufacturing defects, from the date of purchase (if bought in store) or date of delivery (if bought online), at no additional cost for normal (non-professional or commercial) household use. -
Page 42: Uk Declaration Of Conformity
UK declaration of conformity EHTP22 (UK) DECLARATION OF CONFORMITY Product > Hedge Trimmer > EHTP22 > 000001 - 999999 Name and address of the manufacturer or his authorised representative: Kingfisher International Products Limited 3 Sheldon Square London W2 6PX United Kingdom This declaration of conformity is issued under the sole responsibility of the manufacturer. -
Page 43: Ec Declaration Of Conformity
EC declaration of conformity EHTP22 (EN) EU DECLARATION OF CONFORMITY (FR) DÉCLARATION UE DE CONFORMITÉ (PL) DEKLARACJA ZGODNOŚCI UE (RO) DECLARAȚIA DE CONFORMITATE UE (ES) DECLARACIÓN UE DE CONFORMIDAD (PT) DECLARAÇÃO DE CONFORMIDADE UE Product/ Produit/ Produkt/Produsul/Produkt/Producto/Produto > Hedge Trimmer/Taille-haie/Nożyce do żywopłotów/Mașina de tuns garduri vii/Cortasetos/Aparador de sebes >... - Page 44 EC declaration of conformity EHTP22 The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: L’objet de la déclaration décrit ci-dessus est conforme à la législation d’harmonisation de l’Union applicable: Wymieniony powyżej przedmiot niniejszej deklaracji jest zgodny z odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego: Obiectul declarației descris mai sus este în conformitate cu legislația relevantă...
- Page 45 EC declaration of conformity EHTP22 Measured Sound Power Level/ Le niveau de puissance acoustique mesuré/ Zmierzony poziom mocy akustycznej/ Nivel de putere acustică măsurat/ Nivel de potencia sonora medido / Nível de potência sonora medido: 104.3 dB(A) Guaranteed Sound Power Level/ Le niveau de puissance acoustique garant/ Gwarantowany poziom mocy akustycznej/ Nivel de putere acustică...
- Page 46 Manufacturer, Fabricant, Prodecent, Producător, Fabricante: UK Manufacturer: Kingfisher International Products Limited 3 Sheldon Square London W2 6PX United Kingdom EU Manufacturer: Kingfisher International Products B.V. Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.diy.com www.screwfix.com www.screwfix.ie To view instruction manuals online, visit www.kingfisher.com/products...
Need help?
Do you have a question about the EHTP22 and is the answer not in the manual?
Questions and answers