Installation Procedure - Electrolux EHG645BE User Manual

18 electrolux.com.auu
TECHNICAL DATA
EHG755SE EHG755SE EHG955SE EHG955SE
5 5 5 5
Yes, dual Yes, dual Yes, dual Yes, dual
230-240V 230-240V 230-240V 230-240V
Cast Cast Cast Cast
Stainless steel Stainless steel Stainless steel Stainless steel
Ignition through knob Ignition through knob Ignition through knob Ignition through knob
Yes Yes Yes Yes
Stainless steel Stainless steel Stainless steel Stainless steel
NG, (LP conversion kit NG, (LP conversion kit NG, (LP conversion kit NG, (LP conversion kit
supplied) supplied) supplied) supplied)
745 895
530 530
60 60 60 60
55 55 55 55
710 710 860 860
490 490 490 490
5.1 5.1 5.1 5.1
2X9 2X9 2X9 2X9
12.1 12.1 12.1 12.1
24 24 24 24
59.2 59.2 59.2 59.2
EHG955BE EHG955BE EHG953BE EHG953BE
5 5 5 5
Yes, dual Yes, dual Yes, dual Yes, dual
230-240V 230-240V 230-240V 230-240V
Cast Cast Cast Cast
Ceramic glass Ceramic glass Ceramic glass Ceramic glass
Ignition through knob Ignition through knob Ignition through knob Ignition through knob
Yes Yes Yes Yes
Black Black Black Black
NG, (LP conversion kit NG, (LP conversion kit NG, (LP conversion kit NG, (LP conversion kit
supplied) supplied) supplied) supplied)
900 861
530 520
66 66 55 55
55 55 55 55
860 860 830 830
490 490 470 470
5.1 5.1 5.1 5.1
2X9 2X9 2X9 2X9
12.1 12.1 12.1 12.1
24 24 17 17
59.2 59.2 52.2 52.2

INSTALLATION PROCEDURE

1. The bench cutout should be made as per cutout
dimensions in Table 2 and Figure 6.
2. Adjacent walls, cupboards and protection for
combustible materials: Ensure that the appliance
is installed in accordance with AS/NZS 5601.1,
or AS/NZS 5601.2 with regard to clearances
to combustible surfaces and materials, and
clearances to rangehoods and exhaust fans.
To ensure clearances of 200mm from burners
to vertical combustible surfaces observe the
minimum distance requirements shown in Figure 7.
Clearances to combustible surfaces may be
reducedif combustible surfaces are protected
in accordance with AS/NZS 5601.1, or AS/NZS
5601.2.
3. For Ceramic Glass models a FOAM SEAL has
been provided and is to be applied along the
perimeter of the hob.
4. For Stainless Steel models MASTIC TAPE has
been provided and is to be placed around the
bench cutout as specified in Figure 8. Take care to
ensure that the seals meet without overlapping.
5. Fit the pull down clamps supplied to ensure that
the cooktop cannot move after installation.
6. On Stainless Steel models remove any excess seal
visible after installation.
WARNING!
Failure to fix the cooktop to the bench could result in
loosening of the gas connection through movement of the
cooktop and a gas leak may result.
Four clamps and screws are supplied with 3/4-burner
models and six clamps and screws are supplied with
5-burner models. Fit the clamps as shown in Figure 8.
When benchtops are less than 33mm in thickness, it may
be necessary to fit a spacer between the benchtop and
each clamp to ensure clamps can be tightened sufficiently.
Scale: 1:1
19