Table of Contents
Advertisement
Model 675 Series Submersible Level Transmitter
2.3
Operational Checkout (continued)
NON RENEWABLE DESICCANT
INSTALL IN A DRY ENVIRONMENT
3
3
8.00
2.4
Mounting
1.00
THIS DRAWING IS THE PROPERTY OF AMETEK INC. ALL RIGHTS ARE RESERVED AND NEITHER THIS DRAWING NOR ANY INFORMATION IT
THIS DRAWING IS THE PROPERTY OF AMETEK INC. ALL RIGHTS ARE RESERVED AND NEITHER THIS DRAWING NOR ANY INFORMATION IT
CONTAINS IS TO BE COPIED, REPRODUCED, DISCLOSED TO OTHERS, OR USED WITHOUT WRITTEN PERMISSION FROM AMETEK INC.
CONTAINS IS TO BE COPIED, REPRODUCED, DISCLOSED TO OTHERS, OR USED WITHOUT WRITTEN PERMISSION FROM AMETEK INC.
2.4.1 Dimensions
20 AWG LEADS
D
D
.312
POTTED CABLE END
(DO NOT REMOVE)
1.25
1.05
X2
.25 THRU
C
C
1.25
1.0 HEX
DIAPHRAGM
B
B
3.495
2.4.2 Placement
DIAPHRAGM
SURFACE
BOTTOM VIEW WITH
PROTECTIVE PLATE REMOVED
3
3
A
A
3
3
CAUTION: Do not simulate an increase in pressure by applying mechanical
force to the sensing diaphragm of the transmitter. Excessive force will result
8.00
in damage to or destruction of the transmitter.
2
2
When pressure is applied to the transmitter, the display should increase,
1.00
3
3
and then return to the original reading when pressure is removed. The
Transmitter can be pressurized by lowering it into water or by applying air
20 AWG LEADS
pressure from a calibration device.
.312
POTTED CABLE END
NON RENEWABLE DESICCANT
(DO NOT REMOVE)
INSTALL IN A DRY ENVIRONMENT
4
4
1.25
1.00
LIMITS OF ACCEPTABLE WORKMANSHIP ARE DEFINED IN MS-645-A.
LIMITS OF ACCEPTABLE WORKMANSHIP ARE DEFINED IN MS-645-A.
1.05
X2
.25 THRU
.312
.74
1.25
CABLE
SPECIFIED IN
1.05
THE MODEL CODE
X2
.25 THRU
1.25
1" HEX
.74
1.0 HEX
OPTIONAL
CONDUIT ADAPTOR
10.29
1.0 HEX
3.495
SURFACE
1.00
BOTTOM VIEW WITH
PROTECTIVE PLATE REMOVED
3
3
4.75
3.495
DIAPHRAGM
SURFACE
The Model 675 Transmitter should be supported by customer-installed
strain relief cable that is attached to the tabs on the transmitter or optional
BOTTOM VIEW WITH
factory stainless steel support cable #K515183. Reference Figure 2-2 for
PROTECTIVE PLATE REMOVED
installation recommendations. Ametek does not recommend suspending the
2
2
3
3
transmitter supported only by its attached electrical cable.
Caution: Do not allow transmitter to remain in liquid when it freezes solid.
This will apply mechanical force to the sending diaphragm of the transmitter.
Excessive force will result in transmitter damage or destruction.
4
4
2
2
2
2
ALL SHEETS OF THIS DOCUMENT ARE THE SAME REVISION LEVEL.
ALL SHEETS OF THIS DOCUMENT ARE THE SAME REVISION LEVEL.
REFER TO SHEET 1 FOR REVISION HISTORY.
REFER TO SHEET 1 FOR REVISION HISTORY.
8.00
3
3
CABLE
SPECIFIED IN
THE MODEL CODE
20 AWG LEADS
1" HEX
NON RENEWABLE DESICCANT
INSTALL IN A DRY ENVIRONMENT
POTTED CABLE END
(DO NOT REMOVE)
OPTIONAL
CONDUIT ADAPTOR
CABLE
SPECIFIED IN
THE MODEL CODE
1.57
10.29
1" HEX
.74
1.05
CONDUIT ADAPTOR
X2
1.00
1.25
10.29
4.75
1.00
1.0 HEX
2
2
4.75
820 PENNSYLVANIA BOULEVARD, FEASTERVILLE, PA 19053
820 PENNSYLVANIA BOULEVARD, FEASTERVILLE, PA 19053
SIZE
SIZE
CAGE CODE
CAGE CODE
C
C
65048
65048
3.495
SCALE
SCALE
3:4
DIAPHRAGM
2
2
SURFACE
3
3
4
ALL SHEETS OF THIS DOCUMENT ARE THE SAME REVISION LEVEL.
ALL SHEETS OF THIS DOCUMENT ARE THE SAME REVISION LEVEL.
REFER TO SHEET 1 FOR REVISION HISTORY.
REFER TO SHEET 1 FOR REVISION HISTORY.
1
1
ALL SHEETS OF THIS DOCUMENT ARE THE SAME REVISION LEVEL.
ALL SHEETS OF THIS DOCUMENT ARE THE SAME REVISION LEVEL.
D
D
8.00
1.57
1.00
C
C
20 AWG LEADS
.312
1.57
POTTED CABLE END
(DO NOT REMOVE)
1.25
CABLE
OPTIONAL
SPECIFIED IN
THE MODEL CODE
.25 THRU
.74
B
B
1.25
10.29
820 PENNSYLVANIA BOULEVARD, FEASTERVILLE, PA 19053
820 PENNSYLVANIA BOULEVARD, FEASTERVILLE, PA 19053
SIZE
SIZE
CAGE CODE
CAGE CODE
C
C
65048
65048
SCALE
SCALE
3:4
1.00
A
A
U.S.GAUGE DIVISION
PMT PRODUCTS
820 PENNSYLVANIA BOULEVARD, FEASTERVILLE, PA 19053
820 PENNSYLVANIA BOULEVARD, FEASTERVILLE, PA 19053
DWG NO.
DWG NO.
REV
REV
SIZE
SIZE
C
C
K780728
H
C
C
WEIGHT
WEIGHT
SHEET
SHEET
4.75
2 OF 2
SCALE
SCALE
1
1
BOTTOM VIEW WITH
PROTECTIVE PLATE REMOVED
1
1
D
D
1
1
REFER TO SHEET 1 FOR REVISION HISTORY.
REFER TO SHEET 1 FOR REVISION HISTORY.
2
2
C
C
B
B
1.57
1" HEX
OPTIONAL
CONDUIT ADAPTOR
A
A
U.S.GAUGE DIVISION
PMT PRODUCTS
DWG NO.
DWG NO.
REV
REV
C
C
K780728
H
WEIGHT
WEIGHT
SHEET
SHEET
2 OF 2
1
1
U.S.GAUGE DIVISION
PMT PRODUCTS
CAGE CODE
CAGE CODE
DWG NO.
DWG NO.
REV
REV
C
C
65048
65048
K780728
H
WEIGHT
WEIGHT
SHEET
SHEET
3:4
2 OF 2
1
1
2
2
D
D
ALL SHEE
ALL SHEE
C
C
B
B
A
A
820
820
SI
SI
C
C
SCA
SCA
Advertisement
Table of Contents
