Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper FAN7C
Summary of Contents for Draper FAN7C
-
Page 2: Preface
All photographs and drawings within this manual are document is part of the product; retain it for the life supplied by Draper Tools to help illustrate correct of the product, passing it on to subsequent holders. operation of the product. -
Page 3: Table Of Contents
2. Contents 1. Preface 1.1 Product Reference 1.2 Revisions 1.3 Understanding the Safety Content of This Manual 1.4 Copyright © Notice 2. Contents 3. Warranty 4. Product Introduction 4.1 Intended Use 4.2 Specification 5. Health and Safety Information 5.1 General Health and Safety Precautions For This Product 6 5.2 Battery Safety 5.3 Connection to the Power Supply 5.4 Connection to the Power Supply (Charger) -
Page 4: Warranty
This warranty period covers parts and labour for 12 months from the date of Your Draper Tools guarantee is not effective until you can purchase. Where tools have been hired out, the warranty produce, upon request, a dated receipt or invoice to period covers 90 days from the date of purchase. -
Page 5: Product Introduction
Part of our core range, this product is suitable for regular use by enthusiasts and tradespersons alike. 4.2 Specification Stock No. 70975 Part No. FAN7C Rated voltage: 220–240V Rated frequency: 50Hz Rated input: Fan speed:... -
Page 6: Health And Safety Information
• If the supply cord is damaged, it must be replaced by appliance in a safe way and understand the hazards Draper Tools or its authorised service agent in order involved. to avoid a hazard. -
Page 7: Battery Safety
• If the power supply cord is damaged, it must be replaced by Draper Tools, an authorised service agent or similarly qualified personnel in order to avoid a hazard. • The damaged or incomplete plug, when cut from the cable, shall be disabled to prevent connection to a live electrical outlet. -
Page 8: Identification And Unpacking
6. Identification and Unpacking 6.1 Product Overview (10) (11) Front grille Upper grille clip Rear grille Handle loop Blades Cable eyes Fan head (10) Base bracket Control panel (11) Power cable and plug Grille clips – 8 –... -
Page 9: What's In The Box
If any part occurred during shipment. is damaged or missing, do not attempt to use the product. Please contact the Draper Helpline; contact details can be found at the back of this manual. (K) (I) (J) -
Page 10: Operating Instructions
7. Assembly Instructions Important: Read and understand all the safety 4. Slide the blade assembly (D) onto the fan bolt so that instructions listed in this manual before attempting the open face is directed to the rear of the fan. to assemble or install the product. - Page 11 7. Assembly Instructions 6. Pass the grille cap (E) pin through the centre-most 8. Align the grille safety screw holes at the bottom of the opening of the front grille so that it sits within the grill frame and hook the upper clip (7) over the top of sunken area and fix it in place with the 3 x 5mm the rear grille frame.
-
Page 12: Installation Instructions
8. Installation Instructions Important: Read all the safety instructions before attempting to install this product. (10) 8.1 Installing the Fan Onto a Wall Important: The fan requires an area of at least W 600 x H 600 x D 650mm in order to operate freely and without obstruction. -
Page 13: Operating Instructions
9 . Operating Instructions 9.2 Power and Speed Selection Important: Before using this product, read and understand all the safety instructions listed in this manual. ALWAYS ensure that the fan is securely installed To switch the fan on, press the on/speed button (19). and that both grilles are fitted correctly before use. -
Page 14: Fan Modes
9 . Operating Instructions 9.4 Fan Modes The fan is equipped with three modes of operation. Each The fan retains the mode that was active at the time mode can operate at each of the three speeds available. it was switched off and starts up in this mode. The active mode is identified by the colour of the mode The fan mode is managed using the remote control indicator (18). -
Page 15: Shutdown Timer
9 . Operating Instructions 9.5 Shutdown Timer The fan is equipped with a timer that automatically as appropriate to indicate the remaining time. switches the device off after the configured period. Important: The timer is cancelled if the fan is Shutdown occurs regardless of mode or speed. -
Page 16: The Remote Control
10. The Remote Control 10.3 Mode Selection Important: Some functions are only accessible via the remote control. Keep it safe. The fan is equipped with three airflow modes; see 9.4 10.1 Remote Control Overview Fan Modes. The mode must be selected using the remote control. -
Page 17: Maintenance And Storage
11 . Maintenance and Storage Important: Read all the safety information listed in this manual before attempting to maintain, service or repair this product. WARNING! ALWAYS ensure that the fan is switched off, disconnected from mains power and that the blades have completely stopped before working on this product. -
Page 18: Spares, Returns And Disposal
Draper Tools Product Helpline for details of your nearest authorised agent. Draper Tools will endeavour to hold any spare parts, if applicable, for seven years from the date that it sells the final matching stock item. -
Page 19: Explanation Of Symbols
13. Explanation of Symbols Read the instruction manual Shutdown timer (max. 7.5h) 7.5h Warning! Class II appliance WEEE – Do not incinerate or throw onto fire Waste Electrical & Electronic Equipment Do not dispose of this product with domestic waste 220- Rated voltage European conformity... - Page 20 Telephone Sales Desk: +44 (0) 23 8049 4333 General Enquiries: +44 (0) 23 8026 6355 General Fax: +44 (0) 23 8026 0784 Please contact the Draper Tools Product Helpline for repair and servicing enquiries. © Published by Draper Tools Limited © Published by Draper Tools Limited...
Need help?
Do you have a question about the FAN7C and is the answer not in the manual?
Questions and answers