Table of Contents
Advertisement
Quick Links
20" FLOOR STANDING
FAN
09408
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these
instructions before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been
designed, and contains all the necessary information to ensure its correct and safe use. By following all the
general safety instructions contained in this manual, it will ensure both product and operator safety, together
with longer life of the product itself.
AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper
Tools policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Draper 09408
Summary of Contents for Draper 09408
- Page 1 AlI photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Introduction
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS 1. TITLE PAGE 1.1 INTRODUCTION......................2 1.2 REVISION HISTORY ....................2 1.3 UNDERSTANDING THIS MANUAL ................2 1.4 COPYRIGHT NOTICE ....................2 2. CONTENTS 2.1 CONTENTS ........................3 3. GUARANTEE 3.1 GUARANTEE ....................... 4 INTRODUCTION 4.1 SCOPE......................... 5 4.2 SPECIFICATION ......................5 4.3 HANDLING &... -
Page 4: Guarantee
This guarantee applies in lieu of any other guarantee expressed or implied and variations of its terms are not authorised. Your Draper guarantee is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the guarantee period. -
Page 5: Introduction
INTRODUCTION 4.1 SCOPE The 20" fan described in this booklet is intended for air flow circulation use. 4.2 SPECIFICATION Stock No........................... 09408 Part No...........................HV20F Motor: Rated voltage ........................230V Rated frequency........................50Hz Rated input ...........................150W No. of speeds ..........................3 Dimensions (WxHxD) .................. -
Page 6: Health And Safety Information
HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE When using any type of power tool there are steps that should be taken to make sure that you, as the user, remain safe. Common sense and a respect for the tool will help reduce the risk of injury. Read the instruction manual fully. -
Page 7: Additional Safety Instructions For Fans
Warning: Please read the following instructions carefully, failure to do so could lead to serious personal injury. Draper Tools Ltd., recommends that this fan not be modified or used for any application other than that for which is was designed. If you are unsure of its relative applications, do not hesitate to contact us in writing and we will advise you. -
Page 8: Technical Description
TECHNICAL DESCRIPTION 6.1 IDENTIFICATION Rear grille. Fan blade. Front grille. Height adjustment knob. Oscillation action knob. Speed control switch. Tilt adjustment knob. Fan body. Base. - 8 -... -
Page 9: Unpacking And Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing; please contact the Draper Helpline (the telephone number appears on the Title page) and do not attempt to use the machine. -
Page 10: Assembling The Fan
ASSEMBLING THE FAN 8.1 ASSEMBLING THE BASE Remove clamp screw from column Attach base to column using washer and clamp screw and tighten firmly. 8.2 ATTACH TO BASE Attach fan head to base column and tighten clamp screw securely. - 10 -... -
Page 11: Assembling The Protective Blade Grilles
ASSEMBLING THE FAN 8.3 ASSEMBLING THE PROTECTIVE BLADE GRILLES Remove clamp screws from motor then locate the rear grille the correct position and screw in the clamp screws to secure rear grille. Discard the PVC sleeve on the motor shaft. Slide the fan blade onto the motor shaft until it reaches and aligns with the retaining pin. -
Page 12: Fan Instruction
FAN INSTRUCTION 9.1 SWITCH OPERATION The speed is controlled by rotating the switch located on the fan motor housing: OFF. LOW. MEDIUM. HIGH. Important: Remove the plug from the power supply and wait until the fan has completely stopped rotating before making any adjustments to it. -
Page 13: Maintenance
10. MAINTENANCE Always unplug the fan from the power supply before cleaning. All plastic components should be cleaned with a damp cloth. DO NOT spray with water/cleaning agents or immerse the fan unit in water. Warning: Ensure that any water and/or cleaning detergent DOES NOT enter the motor housing or switch mechanism. -
Page 14: Explanation Of Symbols
11. EXPLANATION OF SYMBOLS 11.1 EXPLANATION OF SYMBOLS Do not dispose of WEEE* unsorted municipal waste. Class I construction (Earthed). - 14 -... -
Page 15: Disposal
12. DISPOSAL 12.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: •... - Page 16 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
Need help?
Do you have a question about the 09408 and is the answer not in the manual?
Questions and answers