Onkyo RF-EX6 Instruction Manual
  1. Manuals
  2. Brands
  3. Onkyo Manuals
  4. Receiver
  5. RF-EX6
  6. Instruction manual
Onkyo RF-EX6 Instruction Manual

Onkyo RF-EX6 Instruction Manual

Rf receiver
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
RF Receiver
RF-EX6
Instruction Manual
Thank you for purchasing the Onkyo RF
Receiver. Please read this manual thoroughly
before making connections and plugging in the
unit. Following the instructions in this manual
will enable you to obtain optimum performance.
Please retain this manual for future reference.
Contents
Introduction.................. 3
About the RF-EX6 ............... 3
Applications ......................... 3
Installation .................... 4
the IR blaster .................... 4
Mounting ............................. 5
the IR emitters .................. 6
terminal ............................ 6
Adapter ............................ 7
Settings ................................ 8
RF Interference .................... 8
Troubleshooting ........... 9
Specifications ................ 10
E
n

Advertisement

Table of Contents
loading

Related Manuals for Onkyo RF-EX6

Summary of Contents for Onkyo RF-EX6

  • Page 1: Table Of Contents

    RF Receiver RF-EX6 Instruction Manual Thank you for purchasing the Onkyo RF Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance. Please retain this manual for future reference.
  • Page 2 Precautions Care From time to time you should wipe the unit with a soft cloth. For heavier dirt, dampen a soft cloth in a weak solution of mild detergent and water, wring it out dry, and wipe off the dirt. Following this, dry immediately with a clean cloth.

  • Page 3: Introduction

    Your devices no longer have to be placed in line of sight but can be operated from virtu- ally any location. The RF-EX6 is a RF Receiver that is used in combination with the RF Remote Controller. The RF Receiver receives radio fre-...

  • Page 4: Installation

    Installation The following components should be present: RF Receiver, power adapter, Mono cable, 3 IR emitters, mounting plate and 4 screws. Before you install the RF Receiver, you should decide which of the set-ups described on p. 3 ap- ply to your needs. It is recommended to read through this manual entirely.

  • Page 5: Mounting

    Installation Mounting The RF Receiver can be mounted to a ceiling, a rack, etc. using the included mounting plate and the 4 screws. Take into account the range and the working angle of the IR blaster as explained on p. 4. Also make sure to place the RF Receiver in a central position aimed directly at your de- vices.

  • Page 6: Using The Mono Cable And The Ir Emitters

    IR emitters as an alternative for the IR blaster. You can use the mono cable to connect an Onkyo component that has an IR IN terminal. Note: It is adviced not to place the RF Receiver inside a metal closet as RF signals can be disturbed by metal objects.

  • Page 7: How To Use The Emitters

    Installation How to use the emitters The IR emitters can be attached to the surround- ing surface facing the remote control sensor or directly to the remote control sensor. 1 Attach the emitters to a surface above, below or in front of the remote control sensor of your devices (for aesthetic appearance or when it is difficult to locate the remote control...

  • Page 8: Settings

    Installation Settings As the RF Receiver “communicates” with the RF Remote Controller, you have to set the same Receiver ID (identity) on both appliances. The settings depend on whether you have a single RF Receiver or multiple RF Receiver. Single RF Receiver When you use only one RF Receiver, you can accept the default setting for the Receiver ID (ID=0).

  • Page 9: Troubleshooting

    Troubleshooting Devices do not respond properly ■ Check if the power adapter is connected and the red LED is on. ■ Check if the ID and channel numbers on the RF Receiver match with the ID and channel numbers on the RF Remote Controller (see p.

  • Page 10: Specifications

    Specifications The specifications and design of this product are subject to change without notice. Hardware Red LED (continuously on when powered, blinking during RF reception) 16 IDs and 4 CHs 4 outputs for mono cable and IR emitters Possibility to have multiple RF Receiver in one home not interfering Po- sitioning: freestanding, mounted horizontally or hanging up side down Dimensions 4.5 x 3.2 x 1.2 inch (113 x 81 x 30 mm)
  • Page 11 Memo...
  • Page 12 Tel: +49-8142-4401-0 Fax: +49-8142-4401-555 http://www.onkyo.net ONKYO CHINA LIMITED Units 2102-2107, Metroplaza Tower I, 223 Hing Fong Road, Kwai Chung, N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039 SN 29343616 (C) Copyright 2003 ONKYO CORPORATION Japan. All rights reserved. HOMEPAGE http://www.onkyo.com/ I0308-1...

Table of Contents