Advertisement
Quick Links
Umi Smart Wireless
Wall panel rotary remote controller
Model: BW01-C(A/B)
Quick installation guide
1
Open the wall panel
with a screw driver.
AC
version
AC version: Connect AC power
and install bottom part to
socket with screw, then clip
panel part to bottom part.
General Purpose
Battery / AC power
Dimming / Color
Battery version
Remove
before use
Battery version:
Battery:
CR2032
Pull out battery
insulation tape.
3
Battery version: Install the
back cover to wall with
screw or adhesive, then clip
panel part to the back cover.
Introduction
This wall panel is designed to control compatible Single color, CCT, RGB, RGB+White
or RGB+CCT LED controllers, drivers or lighting fixtures via Umi wireless protocol. There
are two power supply options with AC power or cell battery. The AC version can fit
traditional wall installation with AC power and the battery version can be easily installed at
any preferred place. Besides ON/OFF and dimming operation, user can also adjust color
and mixing mode by simple double click operation.
AC version installation
1. Open the touch panel
The wall panel needs to be opened before installation. Please use a slot type screw
driver to twist in the bottom side slot and open the panel. Please refer to picture 1.
2. Connect the AC power
Push the top of connector on the bottom part back and insert the L and N AC power
2
cables. The maximum cable gauge is 1.5mm or AWG16.
CAUTION! Cut off the AC power before installation to avoid electric shock!
3. Install the panel
Install the bottom part to wall socket with screws. After the bottom part is installed,
clip the front panel part to the bottom part to finish the installation. Please refer to
picture 3.
Battery version installation
1. Open the touch panel
The wall panel needs to be opened before installation. Please use a slot type screw
driver to twist in the bottom side slot and open the panel. Please refer to picture 1.
4
2. Prepare the battery
For new wall panel, please pull out the insulation tape under the battery. To change
the battery please slide the battery out from the battery socket and install a new one. The
battery type is CR2032. Please refer to picture 2.
3. Install the panel
Install the back cover to preferred place by screw or double side adhesive tape, then
clip the front panel part to the back cover and finish the installation. Please refer to
picture 4.
2
Advertisement
Related Manuals for Rayrun Umi BW01-CA
Summary of Contents for Rayrun Umi BW01-CA
- Page 1 Introduction Umi Smart Wireless Wall panel rotary remote controller This wall panel is designed to control compatible Single color, CCT, RGB, RGB+White or RGB+CCT LED controllers, drivers or lighting fixtures via Umi wireless protocol. There are two power supply options with AC power or cell battery. The AC version can fit General Purpose Model: BW01-C(A/B) traditional wall installation with AC power and the battery version can be easily installed at...
- Page 2 Operation Specification 1. Pair / unpair the wall panel to receiver AC version working voltage AC90-265V Battery version working voltage DC3V, CR2032 battery The wall panel needs to be paired to receiver to work. User can pair up to 5 wall Wireless protocol Umi protocol based on SIG BLE Mesh panels to one receiver and each wall panel can be paired to any receiver.
- Page 3 Umi智能⽆线 简介 墙⾯旋钮遥控器 本旋钮⾯板可以通过Umi⽆线协议控制兼容的单⾊、 CCT、 RGB、 RGBW或 通用型号 RGBCCTLED控制器、 驱动电源或其他照明设备。 本产品有交流供电和纽扣电池 供电的两种版本可供选择， 交流电版本可安装在有零⽕线供电的墙⾯接线盒上， 支持调光/调色 型号:BW01-C(A/B) 电池版本则可以安装在任何需要的位置。 除了基本的开/关和调光功能外， 本产 品还可⽤于多通道灯具， 并通过双击、 三击操作来调整颜⾊和多通道混合模式。 快速安装指南 交流供电版本的安装⽅法 1.打开⾯板 电池版 安装前需要先打开本产品。 请使⽤⼀字型螺丝⼑插⼊底部侧槽并旋转螺丝 ⼑来撬开⾯板。 请参考图1。 使⽤前 2.连接交流电 移除 按下底部接线座的塑料按钮， 并接⼊交流电零线和⽕线。 电缆的最⼤尺⼨为 1.5mm 。 电池: ⽤螺丝⼑打开⾯板 电池版本: 警告！...
- Page 4 规格 操作⽅法 1.配对到灯具或控制器 AC90-265V 交流版⼯作电压 本产品需要与灯具或控制器配对才能⼯作。 ⼀个灯具或控制器最多可以配对5个 DC3V,CR2032纽扣电池 电池版⼯作电压 遥控器， 遥控器则可以与任意匹配灯具或控制器配对。 Umi协议， 基于SIGBLEMesh ⽆线协议 请按以下步骤操作来完成遥控器配对或取消配对： 2.4GHzISMband 频段 1).将⽬标灯具或控制器断电， 在超过5秒后再通电。 <7dBm 发射功率 2).在灯具或控制器通电后的10秒内， 快速连续按下旋钮5次完成配对； 或者快速 -20-55°C(-4-131°F) ⼯作温度 连续按下7次取消配对。 86x86x10mm ⾯板部分尺⼨ 2.开/关灯 按下旋钮打开/关闭灯光。 当灯关闭时， 顺时针旋转旋钮也会将灯打开到之 前的亮度。 3.开启到最低亮度 当灯关闭时， 逆时针旋转旋钮将把灯打开到最低亮度级别。 4.调节亮度 顺时针旋转旋钮调亮， 逆时针旋转调暗。 旋钮没有位置限制， ⽤⼾可以向⼀ 个⽅向⽆限旋转旋钮。...