Related Manuals for N&W Global Vending Snakky
Summary of Contents for N&W Global Vending Snakky
- Page 1 INSTALLATION, USE AND MAINTENANCE MANUAL Snakky English DOC. NO. H 180U 02 EDITION 3 2003-06...
- Page 3 Targhetta di identificazione Identification label Valbrembo, 01/01/2012 DICHIARAZIONE DI CONFORMITA’ DECLARATION OF CONFORMITY DÉCLARATION DE CONFORMITÉ KONFORMITÄTSERKLÄRUNG DECLARACIÓN DE CONFORMIDAD DECLARAÇÃO DE CONFORMIDADE VERKLARING VAN OVEREENSTEMMING Italiano Si dichiara che la macchina, descritta nella targhetta di identificazione, è Direttive europee Sostituita da conforme alle disposizioni legislative delle Direttive Europee elencate a lato e suc- European directives...
- Page 4 Declaration of conformity for scrapping T�� s��b�� s���s ���� ��� ������� ��� ��� be disposed of as common waste, but it must b� ��s��s�� �� �s �� �s �s��b��s��� b� ��� T�� ����������� �� ���������� ���� ��� �������� ������ 2002/96/CE (Waste Electrical and Electronics ��v�s ���...
-
Page 5: Table Of Contents
English TABLE OF CONTENTS INTRODUCTION PAGE 2 OPERATING MODES PAGE 12 USER INTERFACE PAGE 12 IDENTIFICATION OF THE VENDING MACHINE PAGE 2 NORMAL OPERATING MODE PAGE 12 IN THE EVENT OF FAILURES PAGE 2 FILLER MENU PAGE 12 TRANSPORT AND STORAGE PAGE 2 STATISTICS PAGE 13... -
Page 6: Introduction
IN Case Of faIlURe In most cases, any technical problems are corrected by INTRODUCTION small repair operations; however, before contacting the manufacturer we recommend that this manual be read This technical documentation is part and parcel of carefully. the machine and must always follow the machine in Should there be serious failures or malfunctions, contact case it is moved or ownership is transferred, so as the following:... -
Page 7: Using The Vending Machine
USING THE VENDING MACHINE FOR PACKAGED PRODUCTS A different sale price can be set for each product selection by the machine electronic control. The various functions are programmed through the selection keypad without any need for additional equipment. All models are equipped with variable configuration trays, adding or removing dividers, spirals and ratiomotors;... -
Page 8: Technical Specifications
PAYMENT SYSTEM TECHNICAL SPECIFICATIONS The machine is supplied with all electrical prearrangement for systems with Executive, BDV and MDB protocol, as Power supply voltage 230 V well as for installation of 24 V DC validators. Beside the coin mechanism housing, suitable space is Power supply frequency 50 Hz provided for the installation (optional) of the most widely... -
Page 9: Changeable Combination Lock
To change combination do as follows: CHANGEABLE COMBINATION LOCK - open the machine door to avoid forcing the rotation; Some machine models are fitted with a changeable com- bination lock. - lightly lubricate the inside of the lock with a spray; The lock is supplied with a silver colour key to be used for - insert the current change key (black) and rotate to the normal opening and closing. -
Page 10: Loading And Cleaning
CONFIGURING THE SPIRALS Chapter 1 LOADING AND CLEANING According to the size of the products to be dispensed, each machine can be fitted with a variable number of trays (maximum 6), product compartments and with dispensing MAIN SWITCH spirals of different pitch. When extracting the sliding compartment,a special switch (see Fig. -
Page 11: Hygiene And Cleaning
As standard feature or using special kits, the machine can HYGIENE AND CLEANING be equipped with small compartments, suitable for dis- According to current health and safety regulations, the pensing cans, plastic bottles up to 69 mm dia., 0.2 litre operator of vending machines is responsible for their Tetra-Paks. -
Page 12: Start-Up
- Load all products starting at the front, without inserting products with a temperature above 30°C, ensuring that all spaces are filled. The bottom of the product must rest at the bottom of the compartment with the label 1 - Product spacer facing the window so that it can be identified. -
Page 13: Installation
INSTALLING THE PAYMENT SYSTEM Chapter 2 INSTALLATION The machine is sold without payment system, there- fore the installer of such a system has sole responsi- bility for any damage to the machine or to things and The machine installation and the following mainte- persons caused by incorrect installation. -
Page 14: Connection To The Power Supply
CONNECTING THE MACHINE CONTROLS AND INFORMATION TO THE POWER SUPPLY The user controls and information are located on the outside of the sliding compartment (see Fig. 14). The machine is designed to operate under a single-phase The credit and all function messages are indicated on the 230 V~ voltage and is protected by T6.3 A fuses. -
Page 15: Internal Components
MAIN SWITCH INTERNAL COMPONENTS The evaporator assembly mounted on the cabinet shelf The power supply unit (see Fig. 28) is fitted with a comprises two fans, the evaporator, the air duct and a microswitch that, when opening the sliding compartment, water retaining tray placed under the evaporator. -
Page 16: Operating Modes
OPERATING MODES NORMAL OPERATING MODE The machine is preset to “Normal operation” mode when The machine control software has three different function connected to the power supply and the payment system levels, which are: door is closed (see door switch - Fig. 24). - normal operation;... -
Page 17: Statistics
STATISTICS PRICES FOR SINGLE SELECTIONS Data on the machine operations is stored in both general This function is used to change the sales price for each counters and relative counters, which can be reset without selection according to the time band. losing total data. -
Page 18: Test
DISPENSING DETECTION “Buzzer” The vending machine can be fitted (as standard feature or A series of sounds is emitted. as optional according to the model) with a device that, by “Compressor” means of photocells, detects the passage of dispensed The compressor is activated/disactivated using the “ ” products. -
Page 19: Technician Menu
Statistics Display partial TECHNICIAN MENU Total Using the programming procedures described in this Delete Partial section, it is possible to set all variables regarding ma- Total chine configuration. The machine is preset to “Technician menu” when press- Display relative partial ing the button from the filler menu. -
Page 20: Present Failures
Dispensing compartment lock PRESENT FAILURES When the function “unlock compartment with dispensing” READING and the parameter “out of service if open” are active, the machine will lock if the locking device of the dispensing When the “Failure” function is displayed, press the confirm compartment remains blocked when closed or it does not button “... -
Page 21: Programming The Parameters
PROGRAMMING PARAMETERS The BDV protocol menus are used for defining the follow- ing functions: CASH Type of vending Setting the operating mode for multiple or single dispens- This set of functions controls all parameters regarding the ing. With multiple dispensing, the change is not automati- payment systems and the sales prices. - Page 22 A or (B and C) Accepted coins A and B and C It is possible to define which, among the coins recognised A and B only by the validator, are to be accepted when the change A and (B or C) tubes are full.
- Page 23 RESET SLAVE second selection (only if an MDB payment system or This function, which can be used only with the Snakky SL, validator are used). With other payment systems, it can be resets the machine programming to a non-configured decided whether or not return the entire amount.
- Page 24 SELECTIONS WITH TWO MOTORS DISPENSING COMPARTMENT LOCK PARAMETERS In order to dispense long products, dividers can be fitted The dispensing compartment can be fitted (as standard so that two motors are used for each single selection. feature or as optional according to the model) with a lock With this function the operation of two motors can be device.
- Page 25 DISPLAY MISCELLANEOUS This set of functions is used to manage the messages This set of functions contains some sub-menus, used less indicated on the external display. frequently, which permit control of the functions described below. LANGUAGE There is an option of language, selected among the PASSWORD available ones, to be used for the messages on the display.
-
Page 26: Statistics
Press the confirm button “ ”, and the message “Confirm?” STATISTICS starts blinking. Data on the machine operations is stored in both general Press the confirm button “ ”, the message “Working” is counters and relative counters, which can be reset without displayed for a few seconds and all statistics are reset. -
Page 27: Test
MDB protocol Audit TEST Aud. 1 Money in the tubes SELECTIONS Money present in the change tubes that moment This function is used to simulate the normal dispensing of Aud. 2 Money to the tubes products without inserting any money. Money sent to the change tubes Check the functioning of the motor rotation by pressing the selection buttons. -
Page 28: Gsm
SECURITY CODE MACHINE INFORMATION It is a further alphanumeric code for reciprocal recognition The machine can memorize a series of codes which will between machine and EVADTS terminal. identify it when retrieving statistics. Programming works as in the “Pass” code. More specifically the following can be stored: Connection - 6-digit operator code;... -
Page 29: Maintenance
Chapter 3 MAINTENANCE The maintenance operations described in this chapter should be carried out with the machine energised and therefore by qualified personnel, who are trained in the correct use of the machine and are aware of the specific risks of such condition. To energize the system with the open door, simply insert the special key into the switch on the payment system compartment door (see Fig. -
Page 30: Configuring The Trays
REPLACING THE SPIRALS CONFIGURING THE TRAYS In order to change the number and the set-up of the product holders, proceed as follows: PRODUCT SPACERS - Slide out the concerned tray. The spacers are used when loading “narrow” products. - Rotate the spiral in the opposite direction to the ejec- The spacers should be fitted to contain products, without tion rotation, holding the plastic support flange still, to blocking them, towards the right-hand side of the compart-... -
Page 31: Changing The Number Of Trays
CHANGING THE TRAY CONFIGURATION CHANGING THE NUMBER OF TRAYS The vending machines are supplied with 6 trays. The configuration of the spirals on each tray can be It is however possible to bring the number of trays to 5, changed. To go from two selections with single spirals to proceeding as follows: one selection with double spirals, do as follows: - Disconnect the plug from the power supply. -
Page 32: Power Supply Unit
POWER SUPPLY UNIT Fuses, switch and connectors positioned at the front of the power supply unit have the functions indicated below. When replacing any fuses the power supply cable must be disconnected from the mains. Fig. 25 Anti-intrusion grille Dispensing compartment Photocell support Fig. -
Page 61: Wiring Diagram
WIRING DIAGRAM LEGEND INITIALS DESCRIPTION INITIALS DESCRIPTION FILTER CONDENSER CM0-9 VENDING MOTOR CAM DIODE EXECUTIVE COIN MECH CONNECTO RADIO INTERFERENCE SUPPRESSO PHOTODIODE PHOTOTRANSISTOR DOOR SWITCH LIQUID CRYSTAL DISPLAY M1-... RELEASE MOTOR CONNECTOR FOR MDB COIN MECH COMPRESSOR TEMPERATURE PROBE RS232 SERIAL PORT BALLAST OUT/R BOARD... - Page 62 This drawing contains confidential information and is the property of the holding company of N&W or one of its subsidiaries, without whose permission it may not be copied or disclosed to third parties of otherwise used. This drawing has to be returned promptly upon request to N&W SX 6085 368 04 ...
- Page 63 Snakky SCHEMA ELETTRICO - WIRING DIAGRAM MACCHINA - MACHINE...
- Page 64 NECTA VENDING SOLUTIONS SpA Sx36901...
- Page 65 Snakky...
- Page 66 © by NECTA VENDING SOLUTIONS SpA NOTE...
- Page 67 The Manufacturer reserves the right to modify, without prior notice, the characteristics of the equipment described in this publication; and further declines to accept any responsibility for any inaccuracies contained in this publication which can be ascribed to printing and/or transcription errors. All instructions, drawings, tables and information contained in this publication are confidential and can neither be repro- duced completely or in part, nor be transmitted to third parties without the written permit of the Manufacturer, who has the sole ownership.