Related Manuals for N&W Global Vending Snakky RY
Summary of Contents for N&W Global Vending Snakky RY
- Page 1 InstallatIon, Use and maIntenance Snakky Ry english H 294U 00 06 - 2007 dition...
- Page 3 DICHIARAZIONE DI CONFORMITA’ DECLARATION OF CONFORMITY DÉCLARATION DE CONFORMITÉ KONFORMITÄTSERKLÄRUNG DECLARACIÓN DE CONFORMIDAD DECLARAÇÃO DE CONFORMIDADE VERKLARING VAN OVEREENSTEMMING INTYG OM ÖVERENSSTÄMMELSE OVERENSSTEMMELSESERKLÆRING YHDENMUKAISUUSTODISTUS Valbrembo, 01/04/2005 Dichiara che la macchina descritta nella targhetta di identificazione, è conforme alle disposizioni legislative delle direttive: 98/37/CE, 89/336, 73/23 CEE e successive modifiche ed integrazioni.
-
Page 5: Table Of Contents
English tablE of contEnts pagE pagE introduction filler menu identification of the vending machine statistics in case of failure selection prices transport and storage change tubes control using the vending machines for packaged products special selections positioning the vending machine test warning for installation gsm pre... -
Page 6: Introduction
iN caSE of failuRE In most cases, any technical problems are corrected by iNtRoductioN small repair operations; however, before contacting the manufacturer we recommend that this manual be read this technical documentation is part and parcel of carefully. the machine and must always follow the machine in should there be serious failures or malfunctions, contact case it is moved or ownership is transferred, so as the following:... -
Page 7: Using The Vending Machines For Packaged Products
uSiNg thE vENdiNg machiNES foR WaRNiNg foR iNStallatioN packagEd pRoductS the machine installation and the following mainte- A different sale price can be set for each product se- nance operations should be carried out by qualified lection by the machine electronic control. The various personnel only, who are trained in the correct use functions are programmed through the selection keypad of the machine according to the standards in force. -
Page 8: Technical Specifications
tEchNical SpEcificatioNS aymeNt system The machine is supplied with all electrical prearrange- Height 1700 ment for systems with Executive, BDV and MDB proto- col, as well as for installation of 24 V DC validators. Width Beside the coin mechanism housing, suitable space is Depth provided for the installation (optional) of the most widely Overall depth with door open... -
Page 9: Changeable Combination Lock
chaNgEablE combiNatioN lock to change combination do as follows: open the machine door to avoid forcing the rotation; Some machine models are fitted with a changeable combination lock. lightly lubricate the inside of the lock with a spray; The lock is supplied with a silver colour key to be used insert the current change key (black) and rotate to the for normal opening and closing. -
Page 10: Loading And Cleaning
coNtRolS aNd iNfoRmatioN charter 1 the user controls and information are located on the loadiNg aNd clEaNiNg outside of the sliding compartment (see fig. 6). the credit and all function messages are indicated on the display. maiN SWitch When extracting the sliding compartment, a special switch (see fig. -
Page 11: Configuring The Spirals
coNfiguRiNg thE SpiRalS As standard feature or using special kits, the machine can be equipped with small compartments, suitable for According to the size of the products to be dispensed, dispensing cans, plastic bottles up to 69 mm dia., 0.2 each machine can be fitted with a variable number of litre Tetra-Paks. -
Page 12: Hygiene And Cleaning
hygiENE aNd clEaNiNg loadiNg pRoductS According to current health and safety regulations, the Remove one tray at a time, lifting it and pulling it past operator of vending machines is responsible for their the retaining slide (see fig. 11). hygiene and cleaning. The vending machine is not suitable for outdoor instal- lation. -
Page 13: Power-On
Power-on all products should load easily, do not insert prod- ucts which are too large for the space. Each time the machine is switched on, the number The sealed edge of the bags may be caught under the of trays and compartments actually connected to the spiral, preventing the free fall of the bag;... -
Page 14: Installation
iNStalliNg thE paymENt SyStEm charter 2 iNStallatioN the machine is sold without payment system, therefore the installer of such a system has sole responsibility for any damage to the machine or to the machine installation and the following mainte- things and persons caused by incorrect installation. nance operations should be carried out by qualified Install the coin mechanism paying attention, according to personnel only, who are trained in the correct use... -
Page 15: Connecting To The Power Supply
coNNEctiNg to thE poWER Supply iNtERNal compoNENtS The machine is designed to operate under a single- The evaporator assembly mounted on the cabinet shelf phase 230 V~ voltage and is protected by T6.3 A fuses. comprises two fans, the evaporator, the air duct and a Before making the connection, ensure that the rating water retaining tray placed under the evaporator. -
Page 16: Dispensing Compartment Manual Unlock
diSpENSiNg compaRtmENt inside the refrigerated box is differentiated between the upper three trays (12°-16° C) and the lower three trays maNual uNlock (8°-10° C). Some models are fitted with a lock device in the dis- The cooling unit is defrosted automatically every 6 hours. pensing compartment that is unlocked through electric The defrosting time can be programmed directly from control when a selection is made (see compartment lock... -
Page 17: Notes On Programming
When closing the machine door, the display indicates the version number of the installed software. SELECTION NOT AVAILABLE “Failure name” Snakky Ry Rev x.x At the end of dispensing, for a few seconds the display indicates the message to pick up the product and the The machine can be programmed for displaying, for a machine is preset for the next selection. -
Page 18: Filler Menu
fillER mENu SuRfiNg modE The interaction between system and operator happens When pressing once the programming button (see fig. through the following components: 18) located on the C.P.U. board, the machine goes into Liquid Crystal Display (LCD), 2 lines x 16 characters. “Filler menu”... -
Page 19: Selection Prices
StatiSticS eletiNg Statistics can be reset for relative counters globally (all Data on the machine operations is stored in both gen- types of data) or selectively for: eral counters and relative counters, which can be reset selections without losing total data. Failures riNtiNg Connect an RS232 serial printer having a Baud rate of... -
Page 20: Special Selections
SpEcial SElEctioNS The monitored devices are: “keypad” Press the button requested on the display; if it works cor- irtUal selectioNs rectly the request for the next button is presented. This function is used to define a pair of selections that can be sold at a price different from the sum of the two “temperature”... -
Page 21: Technician Menu
tEchNiciaN mENu dispensing compartment lock With the “compartment unlock with dispensing” function Using the programming procedures described in this enabled, the failure is indicated if the locking device is section, it is possible to set all variables regarding ma- not unlocked and relocked within a certain time from chine configuration. -
Page 22: Programming The Parameters
pRogRammiNg thE paRamEtERS xecUtive The following payments systems are available for the Executive system: This set of functions controls all parameters regarding - standard the payment systems and the sales prices. - Price Holding � - coges TECH> TECH> � SET PARAMETERS CASH - U-Key... - Page 23 value of “exact amount” This value defines the combination of empty coin tubes, The MDB protocol menus are used for defining the fol- setting the coin mechanism in “exact amount” mode. The lowing functions: possible combinations of empty coin tubes are indicated type of vending below.
- Page 24 ommoN fUNctioNs ombiNeD electioNs Some menus are available, common to the three proto- a combined selection is intended as the association of cols, used for defining the following functions: two selections, one from the master and one from the slave, to the same number (80 to 89) sold at a single mmeDiate cHaNge price.
- Page 25 set a rotation time for each spiral for settling beyond the electioNs witH two motors normal rotation; In order to dispense long products, dividers can be fitted so that two motors are used for each single selection. return or not the paid amount; With this function the operation of two motors can be block further selections for the involved spiral.
- Page 26 isplay iscellaNeoUs this set of functions is used to manage the messages this set of functions contains some sub-menus, used indicated on the machine display. less frequently, which permit control of the functions described below. � TECH> TECH> assworD � SET PARAMETERS DISPLAY It is a 5-digit numeric code which is required to access...
- Page 27 StatiSticS esettiNg tHe statistics Data on the machine operations is stored in both gen- Statistics can be reset for counters globally (all types of eral counters and relative counters, which can be reset data) or selectively for: without losing total data. total Relative riNtiNg...
- Page 28 aud. 4 change return “buzzer” Total money returned a series of sounds is emitted. Aud. 5 Excess “compressor” Excess money. Extra amounts paid by the customer The compressor is activated/deactivated using the � that were not returned (in the event there was no and �...
-
Page 29: Evadts Codes
miScEllaNEouS EvadtS codES The EVADTS (European Vending Association Data acHiNe iNformatioN Transfer System) communication protocol has two codes The machine can memorize a series of codes which will for identifying the machine and for recognising the data identify it when retrieving statistics. transfer terminal: More specifically the following can be stored: ass coDe... -
Page 30: Up Key
up kEy The control software can send, via GSM modem, a etUp coNtrol signal indicating a machine failure or an “ending product” “pre-alarm”, after dispensing a programmable number of > veNDiNg macHiNe selections. When confirming this function after inserting the Up-Key in the special port located on the C.P.U. -
Page 31: Printed Board Functions And Indicator Lamps
charter 3 maiNtENaNcE The maintenance operations described in this chapter should be carried out with the machine energised and therefore by qualified personnel, who are trained in the correct use of the machine and are aware of the specific risks of such condition. To energize the system with the open door, simply insert the special key into the switch on the payment system compartment door (see fig. -
Page 32: Configuring The Trays
coNfiguRiNg thE tRayS REplaciNg thE SpiRalS In order to change the number and the set-up of the pRoduct SpacER product holders, proceed as follows: Slide out the concerned tray. The spacers are used when loading “narrow” products. The spacers should be fitted to contain products, without Rotate the spiral in the opposite direction to the ejec- blocking them, towards the right-hand side of the com- tion rotation, holding the plastic support flange still, to... -
Page 33: Changing The Number Of Trays
chaNgiNg thE NumbER of tRayS chaNgiNg thE tRay coNfiguRatioN The vending machines are supplied with 7 trays. The configuration of the spirals on each tray can be It is however possible to bring the number of trays to 5 or changed. -
Page 34: Power Supply Unit
poWER Supply uNit accESS to thE cooliNg uNit The power supply unit is housed in the payment system If for any reason the cooling unit need to be accessed compartment; the fuses and the compartment switch from the machine, do as follows: can be accessed directly, while it is necessary to remove - remove the last tray;... -
Page 35: Programming Menu Summary
pRogRammiNg mENu SummaRy SuRfiNg modE The buttons shown in the figure are used for surfing The machine can function in 3 different operating mo- through the different menus: des: - Normal vending mode - filler menu - technician menu In order to access the programming menus, press the programming button located on the CPU board (see fig. - Page 36 “fillER mENu” SummaRy 1 - STATISTICS 1.1 - PRINT STATISTICS 1.1.1 - PARTIAL PRINTOUT 1.1.1.1 - PRINT SEL. COUNT 1.1.1.2 - PRINT BAND COUNT 1.1.1.3 - PRINT DISC COUNT 1.1.1.4 - PRINT FAIL COUNT 1.1.1.5 - PRNT C MECH DATA 1.1.2 - TOTAL PRINTOUT 1.2 - PRINT REL.
- Page 37 “fillER mENu” SummaRy 1.4 - DIS. REL. STATS 1.4.1 - DIS. SEL. COUNT. 1.4.1.1 - DIS. SIN. COUNT. 1.4.1.2 - DIS. TOT. COUNT. 1.4.1.3 - DIS. SEL. COUNT. 1.4.2 - DIS. BAND COUNT. 1.4.3 - DIS. DISC. SEL. 1.4.4 - DIS. FAIL.COUNT. 1.4.5 - DIS.
- Page 38 “fillER mENu” SummaRy 3 - TUBES CONTROL 3.1 - FILL TUBES 3.2 - RELEASE TUBES 4 - BOILER TEMPERAT. 5 - TEST 5.1 - COMP. DISPENSING 5.2 - WATER ONLY 5.3 - POWDER ONLY 5.4 - NO ACCESSORIES 5.5 - ACCESSORIES ONLY 6 - GSM 6.1 - RESET PRE-AL CNT 7 - EVADTS...
- Page 39 “tEchNiciaN mENu” SummaRy 1 - FAILURES 1.1 - FAILURE READING 1.2 - FAILURE RESET 1.3 - MOTOR ERRORS 1.4 - MOTORS’ STATUS 1.5 - RESET MOTOR ERR. 2 - PROGR.PARAMETERS 2.1 - CASH 2.1.1 - PRICES 2.1.1.1 - INDIVIDUAL PRICE 2.1.1.1.1 - PRICE BAND 0 2.1.1.1.2 - PRICE BAND 1 2.1.1.1.3 - PRICE BAND 2...
- Page 40 “tEchNiciaN mENu” SummaRy 2.1.4 - MASTER SLAVE 2.1.4.1 - IMPOSTAZIONE 2.1.4.2 - SLAVE PRICE HOLD 2.1.4.3 - COMB’D SELECT.S 2.1.4.4 - RESET VM ‘SL’ 2.1.4.5 - MONITOR 2.1.4.6 - SNAKKY TYPE 2.1.5 - FREE VEND BONUS 2.1.5.1 - ENAB. VEND BONUS 2.1.5.2 - BONUS RATE 2.2 - SPIRALS/SELECT.
- Page 41 “tEchNiciaN mENu” SummaRy 2.4 - DISPLAY 2.4.1 - LANGUAGE 2.4.2 - USER DISPLAY 2.4.3 - PROMOT. ADVERT. 2.4.3.1 - ENABLE PROM.ADV. 2.4.3.2 - SET PROM.ADVERT. 2.4.4 - CUSTOMIZ.STRINGS 2.4.4.1 - ENAB. CUSTOM.STR 2.4.4.2 - PRG. CUSTOM.STR. 2.4.5 - COUNTER AT START 2.4.6 - CONTRAST CONTROL 2.5 - MISCELLANEOUS 2.5.1 - SET PASSWORD...
- Page 42 “tEchNiciaN mENu” SummaRy 3.2 - STATISTICS RESET 3.2.1 - PARTIAL RESET 3.2.1.1 - SELE.COUNT.RESET 3.2.1.2 - FAILURE COUNT. 3.2.1.3 - COIN MECH DATA 3.2.1.4 - CANC. PHOT. ERR. 3.2.1.5 - CANC.MOT.ERR.CNT 3.2.2 - TOTAL RESET 3.2.3 - RESET COUNT. TOT 3.3 - DISP.REL.STATS.
- Page 43 “tEchNiciaN mENu” SummaRy 3.6 - STATIST.PRINTING 3.6.1 - PARTIAL PRINTING 3.6.1.1 - SELECT. COUNT. 3.6.1.2 - BAND COUNTER 3.6.1.3 - FAILURE COUNT. 3.6.1.4 - COIN MECH.DATA 3.6.1.5 - PRINT PHOT. ERR. 3.6.1.6 - PRINT MOTOR ERR. 3.6.2 - TOTAL PRINTING 3.7 - PRINT REL.STATS.
- Page 44 “tEchNiciaN mENu” SummaRy 5 - MISCELLANEOUS 5.1 - VEND.MACH. DATA 5.1.1 - INSTALLAT. DATE 5.1.2 - PRG.MACHINE CODE 5.1.3 - OPER. CODE ENTRY 5.2 - INITIALISING DB 5.3 - EVADTS 5.3.1 - PASS.CODE 5.3.2 - SECURITY CODE 5.3.3 - CONNECTION 5.3.4 - PROTOC.
-
Page 45: Wiring Diagram Legend
WiRiNg diagRam lEgENd iNitialS dEScRiptioN iNitialS dEScRiptioN FILTER CONDENSER CONNECTOR FOR MDB COIN MECHANI CM1-.. COFFEE UNIT MOTOR CAM DISP COMPT FLAP MICROSWITCH DISPENSING COMPARTMENT MOTOR CAM COMPRESSOR DIODE EXECUTIVE COIN MECH CONNECTORS TEMPERATURE PROBE RADIO INTERFERENCE SUPPRESSOR RS232 SERIAL PORT PHOTODIODE BALLAST PHOTOTRANSISTOR... - Page 48 N&W GLOBAL VENDING S.P.A. sx436901...
- Page 49 Snakky...
- Page 50 © by N&W GLOBAL VENDING SpA NOTE...
- Page 51 The manufacturer reserves the right to modify, without prior notice, the characteristics of the equipment described in this publication; he declines all responsibility for any inaccuracies due to printing and/or typing errors herein contai- ned. The instructions, drawings, tables and information in general contained in this booklet are of a confidential nature and may not be reproduced entirely or in part or be passed on to a third party without the prior written authorisation of the manufacturer who retains its exclusive ownership.