Related Manuals for Clarke PTE550C
Summary of Contents for Clarke PTE550C
- Page 1 HYDRAULIC PALLET TRUCK MODEL NO: PTE550C PART NO: 7631701 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC11/22...
-
Page 2: Product Specification
220ml Please note that the details and specifications contained herein, are correct at the time of going to print. However, CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 3: Safety Instructions
SAFETY INSTRUCTIONS WARNING: THE TRUCK HAS TO BE USED ON SUBSTANTIALLY FIRM, SMOOTH, LEVEL AND PREPARED SURFACES. THE LOAD MUST BE PLACED CENTRALLY ON THE FORKS. The operator should read all warning signs and instructions here and on the pallet truck before use. 1. -
Page 4: Environmental Protection
18. Load the pallet truck evenly with the centre of gravity of the load above the centre of the forks. DO NOT move unstable or loosely stacked loads. Use extra care when moving long, tall or wide loads which impair your view. - Page 5 ASSEMBLY After unpacking it is necessary to attach the handle assembly as follows: 1. Withdraw the hinge pin (1) from the truck frame. 2. Take the handle assembly and lower the end of the chain through the hole in the pump body so that it emerges at the bottom of the housing.
- Page 6 ADJUSTMENT The control lever has three positions shown and indicated by the label on the handle. • With the lever pulled to the upper position, the forks will lower. • The middle position allows the load to be transported. • The lower position will cause the forks to lift when the handle is pumped.
- Page 7 OPERATING INSTRUCTIONS BEFORE USE Daily inspection is advisable to find any defect of the pallet truck. Check the following points before operation. • Visually check for structural damage and listen for any unusual noise or binding of the lifting mechanism. •...
- Page 8 If the ground is not flat, chock the wheels to stop it moving. MALFUNCTIONS If there is any malfunction stop using the truck until it is repaired by your local CLARKE dealer. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 9: Care And Maintenance
CARE & MAINTENANCE Whilst the pallet truck requires very little maintenance, the following care can be expected. PURGING AIR FROM THE HYDRAULIC SYSTEM If the pallet truck has been transported over any distance or has been overturned at any time, air may have entered the hydraulic system. -
Page 10: Troubleshooting
The forks The piston rod is deformed Replace the piston rod or cannot be resulting from load slanting to return to CLARKE dealer lowered one side or over loading. for overhaul. The fork was kept in the raised Keep the fork in the lowest... - Page 11 DECLARATIONS OF CONFORMITY-PTE550C Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 12 COMPONENT PARTS - FORKS & FRAME Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 13 COMPONENT PARTS - FORKS AND FRAME Description Description Ball Hinge pin Bolt Rear wheel assembly Handle assembly see page 15 Crank arm Hinge pin Circlip Support cuff Bush Pump assembly (see p 14 Bogie assembly Forks Hinge Rod Pivot cuff Circlip Bearing base Connecting rod...
- Page 14 COMPONENT PARTS - PUMP Description Description Pump core O-ring Seal ring Spring cap Screw plug Dust ring Washer Sealing ring Spring Spring Valve body Pump base Valve core Piston rod Steel ball O-ring Spring Magnet Valve body Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 15 Steel balls Valve spring Valve core Lever bracket Washer Nut M6 Screw cap Screw M6x25 Plug Steel ball Seal ring Ball seat COMPONENT PARTS - HANDLE ASSEMBLY No Description Wheel Fixed plate Column Handle Chain Circlip Hinge Bush Spring Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
Need help?
Do you have a question about the PTE550C and is the answer not in the manual?
Questions and answers