Subscribe to Our Youtube Channel
Related Manuals for Clarke Strong-Arm PTE550
Summary of Contents for Clarke Strong-Arm PTE550
- Page 1 HYDRAULIC PALLET TRUCK HYDRAULIC PALLET TRUCK MODEL No: PTE550 PART Nos 7630171 OPERATION & MAINTENANCE INSTRUCTIONS 0604...
-
Page 2: Guarantee
CLARKE GUARANTEE This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase. -
Page 3: Table Of Contents
CONTENTS Guarantee ................2 Contents ................3 Specifications ................ 4 Safety Precautions ..............5 Assembly ................6/7 Operating Instructions ............7/8 Maintenance ................ 8 Parts Diagram ............... 9 Parts List ................10/11 Fault Finding ................ 12 Declaration Of Conformity ..........13 FEATURES •... -
Page 4: Specifications
MAXIMUM LOAD - 2000KG Please note that the details and specifications contained herein are correct at the time of going to print. However CLARKE International reserve the right to change specifications at any time without prior notice. Always consult the machines data plate... -
Page 5: Safety Precautions
Check for signs of cracked welds, bent or loose pins or other signs of structural damage. Do not use if any of these conditions exist. Ensure repairs are carried out by qualified persons only, or contact your nearest Clarke dealer. -
Page 6: Assembly
ASSEMBLY Figures in brackets refer to Index Nos in parts list on pages 9-12 Your new Pallet truck is delivered with the handle removed, To fit the handle proceed as follows; Remove one roll pin, item 1, Fig. 1 (24) from shaft, item 2, Fig. 1 (23) and keep safe for reuse later. -
Page 7: Operating Instructions
Lower Neutral Raise Fig. 3 Fig. 4 Fig. 5 OPERATING INSTRUCTIONS Before operating the truck, ensure you have read and understood the instructions in this manual, paying particular attention to the safety precautions. Familiarise yourself with the controls, i.e; raise and lower the forks without any load, practice steering the empty truck to understand how the truck reacts. -
Page 8: Maintenance
Slowly raise the forks and watch the load lift, once the load has been raised sufficiently, put the trigger in the neutral position (centre), before attempting to move the truck. Gently push or pull the pallet truck with load to its new location, observing that there are no personnel or obstacles in the way. -
Page 9: Parts Diagram
PARTS DIAGRAM... -
Page 10: Parts List
Damping Valve Spindle ZJPTE55029 Damping Valve Seat ZJPTE55030 Steel Ball ZJPTE55031 Base ZJPTE55032 Roll Pin ZJPTE55033 Bowl Washer IMPORTANT: The use of parts other than CLARKE replacement parts may result in safety hazards, decreased tool performance and may invalidate your warranty. - Page 11 PARTS LIST Index No Part No Description ZJPTE55034 Bearing ZJPTE55035 Supporting Base ZJPTE55036 Retaining Ring ZJPTE55037 Steel Ball ZJPTE55038 Piston ZJPTE55039 Dust Ring ZJPTE55040 ‘O’ Ring ZJPTE55041 ‘Y’ Ring ZJPTE55042 Oil Plug ZJPTE55043 Steel Ball ZJPTE55044 Base ZJPTE55045 Spring ZJPTE55046 Regulation Screw ZJPTE55047 Copper Washer...
-
Page 12: Fault Finding
TROUBLE SHOOTING Symptoms Possible Causes Remedy Forks not lifting to Insufficient hydraulic oil. Add more hydraulic oil. maximum height. a) No hydraulic oil. a) Add Hydraulic oil. b) The oil is contaminated. b) Change the hydraulic Forks not lifting. oil. c) The regulating screw c) Slacken locknut (item 10), (item 9) Fig.5 is set too...
Need help?
Do you have a question about the Strong-Arm PTE550 and is the answer not in the manual?
Questions and answers