BEGA 84 234 Installation And Technical Information

BEGA
Installation and Technical Information
Tools Required:
• 3mm hex head screwdriver
• Phillips head screwdriver
• 6mm hex head screwdriver
Overview:
LED Watts: 95.6W
System Watts: 107.0W
Controllability: 0-10V dimmable
Weight: 12.6 lbs.
Protection Class: IP65
Notice to Installer:
1. See page 2 for specific product safety warnings.
2. In conformance with UL Standard 1598, a silicone based sealant must be used
between luminaire and supporting surface.
3. Luminaire mounts directly to standard recessed 4" octagonal wiring (by others),
using mounting plate provided.
Installation: Luminaire
1. Loosen the (1) 3mm hex head set screw on the fixture canopy to remove luminaire
base.
2. Feed luminaire wiring through the luminaire base and mounting plate into wiring box
(by others).
3. Make supply wiring connections to luminaire in wiring box:
MAIN VOLTAGE SUPPLY WIRE TO BLACK LUMINAIRE WIRE
NEUTRAL (COMMON) SUPPLY WIRE TO WHITE LUMINAIRE WIRE
GREEN GROUND WIRE TO GREEN LUMINAIRE WIRE
Dimming (if applicable):
DIMMING CONTROL (+) TO POSITIVE LUMINAIRE DIM CONTROL WIRE
DIMMING CONTROL (-) TO NEGATIVE LUMINAIRE DIM CONTROL WIRE
4. Attach provided mounting plate directly to a 4" standard octagonal wiring box using
the (2) phillips head screws (provided).
5. Important! Place a small bead of silicone around the back side of the mounting
plate that will come in contact with the finished surface (exterior applications only).
Failure to do so can cause water entry and will void warranty.
6. Place luminaire base over the mounting plate. Tighten nuts (provided) on the studs
to secure. (Figure 1)
7. Ensure stainless steel safety cable is connected between luminaire canopy and
luminaire base.
8. Place luminaire over luminaire base, aligning the set screw with the feature shown
in Figure 2. Twist canopy to lock into place.Tighten (1) 3mm hex head set screw to
secure luminaire.
9. To adjust head angle, use 6mm hex head screwdriver to loosen screw at aiming
joint. Aim luminaire head as needed and tighten screw to secure into place.
Accessories
Please refer to the appropriate accessory installation
sheet for further instruction when applicable.
BEGA 1000 Bega Way, Carpinteria, CA 93013 (805)684-0533 © copyright BEGA 2022
Due to the dynamic nature of lighting products and the associated technologies, luminaire data on this sheet is subject to change at the discretion of BEGA North America. For the most current technical data, please refer to bega-us.com
High performance floodlight - narrow beam
A C
B
D
Figure 1:
Figure 2:
Scheinwerfer wie in Skizze dargestellt auf die
Scheinwerfer wie in Skizze dargestellt auf die
Montageplatte setzen, ausrichten und fest
Montageplatte setzen, ausrichten und fest
verschrauben.
verschrauben.
Scheinwerfereinstellung vornehmen:
Scheinwerfereinstellung vornehmen:
Innensechskantschraube (SW 6) lösen und
Innensechskantschraube (SW 6) lösen und
gewünschte Ausstrahlrichtung einstellen.
gewünschte Ausstrahlrichtung einstellen.
Gelenkschraube anziehen.
Gelenkschraube anziehen.
Anzugsdrehmoment = 12 Nm.
Anzugsdrehmoment = 12 Nm.
Lichtstromreduzierung
Lichtstromreduzierung
Neben der digitalen Ansteuerung besteht
Neben der digitalen Ansteuerung besteht
die Möglichkeit, den Lichtstrom über
die Möglichkeit, den Lichtstrom über
einen intergrierten Drehkodierschalter im
einen intergrierten Drehkodierschalter im
Leuchtengehäuse manuell zu begrenzen.
Leuchtengehäuse manuell zu begrenzen.
Gleichzeitig wird hierdurch ein Betrieb bei Gleichzeitig wird hierdurch ein Betrieb bei
höheren Umgebungstemperaturen möglich. höheren Umgebungstemperaturen möglich.
Schalterstellung 0 = 100 % Schalterstellung 0 = 100 % max. t
Schalterstellung 1 = 70 % Schalterstellung 1 = 70 % max. t
Schalterstellung 2 = 50 % max. t
Schalterstellung 2 = 50 %
Dimensions
A: 9-3/4
B: 17-3/8
C: 2-1/8
D: 5-1/8
Place floodlight unit onto the mount
Place floodlight unit onto the mounting plate
Maintenance:
as displayed in the sketch, align and
as displayed in the sketch, align and screw
Clean regularly with solvent-free cleaner
together firmly.
together firmly.
removing dirt and debris. Do not use high
Adjust the floodlight:
Adjust the floodlight:
pressure cleaners.
Undo hexagon socket screw (wrenc
Undo hexagon socket screw (wrench
size 6 mm) and set the desired beam
size 6 mm) and set the desired beam direction.
Tighten the joint screw.
Tighten the joint screw.
Torque = 12 Nm.
Torque = 12 Nm.
Reduction of luminous flux
Reduction of luminous flux
Besides digital control you can limit
Besides digital control you can limit the
Replacement Parts
luminous flux manually by means of
luminous flux manually by means of an
See label inside of fixture for LED replacement
integrated rotary coded switch insid
integrated rotary coded switch inside the
part number.
luminaire housing.
luminaire housing.
Consult factory for all other replacement
components.
By this means an operation at higher ambient By this means an operation at highe
temperatures is possible. temperatures is possible.
: 25 °C max. t : 25 °C Switch position 0 = 100 % Switch position 0 = 100 %
a
a
: 45 °C max. t : 45 °C Switch position 1 = 70 % Switch position 1 = 70 %
a a
: 50 °C Switch position 2 = 50 %
max. t : 50 °C Switch position 2 = 50 %
a a
84 234
Updated: 08/22/22
max. t : 25 °C max
a
84 234 1 of 2
max. t : 45 °C max
a
max. t : 50 °C
max
a