Victor RMR65E Operating Manual

O P E R ATI NG MAN UAL
OPTIMAX REFRIGERATED RETAIL MERCHANDISERS
MODEL NUMBERS
RMR65E/SMR65ECT • Assisted service 650 wide
RMR100E/SMR100ECT • Assisted service 1000 wide
RMR130E/SMR130ECT • Assisted service 1300 wide
RMR65S • Self service 650 wide
RMR100S • Self service 1000 wide
RMR130S • Self service 1300 wide
RMR65SW • Self service - wall 650 wide
RMR100SW • Self service - wall 1000 wide
RMR130SW • Self service - wall 1300 wide
RMR65SP • Pass through - 650 wide
RMR100SP • Pass through - 1000 wide
RMR130SP • Pass through - 1300 wide
(As above with suffix L, which denotes under shelf lighting)
Thank you for buying a Victor Unit. We hope and expect that
you will get many years of satisfactory use from your purchase.
In order to achieve the best results from your equipment please
read, and follow, the installation, operating, cleaning and
maintenance instructions below. Failure to follow them may
affect the warranty.
1. UNPACKING AND ASSEMBLY
All protective coating used on stainless steel surfaces of the hot
cupboard must be removed. The exposed surfaces can then be
wiped clean with a damp cloth, using a mild detergent or soap
if necessary.
Do not use any abrasive material or form of bleach for cleaning
purposes. Please see cleaning section of these instructions.
Mobile Models:
Four Castors are fitted, two of which are braked.
2. INSTALLATION
Position the appliance where it is to be used and ensure that it
is as level as possible.
Do not site the appliance in the immediate vicinity of a heat
source.
Do not position the appliance so as to obstruct air vents on
either the operator or customer sides of the appliance.
Adequate airflows are vital to the correct functioning
of the refrigeration system. Avoid placing the appliance in areas
subject to strong draughts or under air conditioning systems.
Avoid areas subject to high humidity (e.g. conservatories) as the
appliance will act as a de-humidifier, and create excessive
amounts of water.
The appliance is fitted with a 13 Amp fused plug and only
requires connection to a suitable 13 Amp socket outlet. This
model is suitable for 230 - 240V A.C. supply only. Ensure that the
electricity supply is as stated on the model's data plate.
Important:
If the unit you have purchased is not fitted with a 13 amp plug
and lead, this model will need to be connected to the mains via
a suitable isolating switch by a qualified electrician and wired in
accordance with the current edition of the I.E.E wiring
regulations, ensuring the electricity supply is as stated on the
data plate.
Important:
Wires in the mains lead are coloured in accordance with the
following code:
Green and Yellow (Earth) • Blue (Neutral)) • Brown (Live)
Warning: This appliance must be earthed, do not touch internal
wiring.
As the colours of the wires in the mains lead on this appliance
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
(a) The wire which is coloured green and yellow must be
connected to the terminal in the plug, which is marked with
letter E or the symbol .
(b) The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or is coloured black.
(c) The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or is coloured red.
3. USE AND BEST PERFORMANCE
The display is designed to maintain food placed in it at
between 3ºc and 5ºc in ambient temperatures of up to 25ºC
with a relative humidity of up to 60%; food being placed in
the display must be at or below this temperature.
E, S and SP suffix models:
The refrigeration system is operated by a green on / off switch
marked 'Refrigeration' and located at the rear of the unit which
will illuminate when the refrigeration is switched on.
SW suffix models:
Turning the unit on/off on the controller
1. Press and hold the right hand button (X) this will switch on
the unit. The display will now read the unit temperature and
will start to run after one minute.
2. Press and hold the right hand button (X) this will switch off
the unit. The display will now read off.
Turning the light on/off on the controller:
1. Press in the second to right hand button (M). The light will
now be illuminated.
2. Press in the second to right hand button (M). The light will
now go off (this procedure can be carried out even when the
unit is not running and the display reading off ).
The refrigeration system is controlled by a microprocessor
control which is factory set and requires no adjustment. The
digital display will show the air temperature within the well, not