Clean Water 7500-REV2.5 Installation Manual
Sediment backwash filter
Hide thumbs
Also See for 7500-REV2.5:
- Installation manual (20 pages) ,
- Installation manual (14 pages) ,
- Installation manual (8 pages)
Related Manuals for Clean Water 7500-REV2.5
Summary of Contents for Clean Water 7500-REV2.5
- Page 1 Clean Water Made Easy www.cleanwaterstore.com 7500-REV2.5 Sediment Backwash Filter Installation Guide Rev-012623...
- Page 2 Thank you for purchasing a Clean Water System! Please review this start up guide entirely before beginning to install your system, and follow the steps outlined for best results. Minimum pressure of 30 PSI recommended. Maximum pressure recommended 80 PSI.
-
Page 3: Table Of Contents
Programming Your Valve and Setting Time and Days for Backwash Set the Current Time of Day Set the Date Start the First Backwash Advanced Programming Mode Advanced Program Recommended Settings Maintenance Troubleshooting the 7500-REV2.5 Sediment Backwash Filter 7500-REV2.5 Water Filters Limited Warranty Rev-012623... -
Page 4: Packing Lists
7500-REV2.5 Sediment Backwash Filter Installation Guide Packing Lists All systems include: 7500-REV2.5 control valve, bypass valve, power supply, funnel for adding media, start-up guide, and items included in one of the following options: Find Your Size System to See What is Included: Sediment Backwash Filter 0. -
Page 5: Pre-Installation
4. If you will be using copper piping, do not sweat the copper pipe directly on to the 7500-REV2.5 control valve. 5. To connect drain line to drain, use an air-gap connection, so that if your sewer or septic tank backs up, it cannot cross connect with the drain tubing. -
Page 6: How The Bypass Valve Works
7500-REV2.5 Sediment Backwash Filter Installation Guide How the Bypass Valve Works Turn knob so the valve is bypassed when installing. Installation of Your System with Copper or Metal Piping Systems If your new filter system is to be installed in a metal (conductive) plumbing system, i.e., copper, or galvanized steel pipe, the plastic components of the system will interrupt the electrical continuity of the plumbing system. -
Page 7: How Your Sediment Backwash Filter Works
7500-REV2.5 Sediment Backwash Filter Installation Guide How Your Sediment Backwash Filter Works Water enters the top of the tank and flows down through the media and up the distributor tube. The backwashing Sediment Backwash Filter removes sediment and is automatically backwashed. -
Page 8: Diagram Of Typical Installation Well Water
7500-REV2.5 Sediment Backwash Filter Installation Guide Diagram of Typical Installation Well Water Diagrams of Typical Installation City Water Rev-012623 www.cleanwaterstore.com... -
Page 9: Tank Assembly And Installation Instructions
9. Lubricate the main tank O-ring with silicone grease and screw on the 7500-REV2.5 control valve carefully. Do not use pipe-joint compound, vegetable oil, Teflon tape, or Vaseline or other petroleum greases to lubricate tank threads. - Page 10 7500-REV2.5 Sediment Backwash Filter Installation Guide 13. If you are in earthquake zone, strap your backwash filter tank to wall with metal strapping. 14. Proceed to programming your 7500-REV2.5 control valve timer and backwash frequency. IMPORTANT: you must program the time and then start a backwash and rinse.
-
Page 11: Programming Your Valve And Setting Time And Days For Backwash
7500-REV2.5 Sediment Backwash Filter Installation Guide Programming Your Valve and Setting Time and Days for Backwash How to Start a Manual Backwash: Press the Back / Regen button Pressing “Back Regen” at any time results in an immediate manual regeneration. -
Page 12: Set The Current Time Of Day
7500-REV2.5 Sediment Backwash Filter Installation Guide Set the Current Time of Day 1. If LOCK icon is lit, press, and hold both UP and DOWN buttons for 3 seconds to unlock keypad. 2. Then press the MENU/CONFIRM button to enter the main menu. -
Page 13: Start The First Backwash
7500-REV2.5 Sediment Backwash Filter Installation Guide Continue to use this same procedure for changing remaining settings. Set Service Days This is the number of days between backwash. Set for every 1 to 7 days depending on water quality. For example, the default setting is to backwash every 7 days. If you notice pressure loss in the house after 4 days, then change setting to every 3 or 4 days. - Page 14 7500-REV2.5 Sediment Backwash Filter Installation Guide 8. The backwash is now counting down from 10 minutes- you want to keep it in backwash for a while, so unplug the power supply from the wall, and the valve will stay in backwash.
-
Page 15: Advanced Programming Mode
7500-REV2.5 Sediment Backwash Filter Installation Guide Advanced Programming Mode Can be skipped. The Advanced Programming Mode allows you to set the Regen Cycle and Regen Mode. Skip this for most applications as your filter system has already been set to correct mode. -
Page 16: Advanced Program Recommended Settings
7500-REV2.5 Sediment Backwash Filter Installation Guide Advanced Program Recommended Settings Review Company Info CWS 831-462-8500 Set Valve Model 62605 Set Language English Set Company Info CWS 831-462-8500 Set Hour Mode 12 HR Set Time of Day Current time of day... -
Page 17: Maintenance
One problem that may occur is if you do not have enough backwash flow rate to properly clean the Sediment Backwash Filter. You can verify the backwash flow rate by running the drain line into a bucket and timing it when the 7500-REV2.5 is in Cycle 1 or backwash Rev-012623 www.cleanwaterstore.com... -
Page 18: 7500-Rev2.5 Water Filters Limited Warranty
9. Any product returned to Clean Water Store without a valid return authorization number will be rejected. Any product found to be defective will, at the sole discretion of Clean Water Store be repaired or replaced. Clean Water Store is not responsible for shipping cost to the repair facility.
Need help?
Do you have a question about the 7500-REV2.5 and is the answer not in the manual?
Questions and answers
What salt do you use for filter Where do you get it?