Table of Contents
Advertisement
WARNING
To avoid damage from the electronic fuel injection system, do not remove or install the
battery when the ignition switch is in the "
" position.
The long-term storage of the vehicle could cause fuel and engine oil deterioration and
probably get into a non-start situation.
Service more frequently when operating in severe conditions such as dusty area, high
speed riding, frequent start and stop or extreme riding habit.
Make sure to keep away from any flammable materials such as dry grasses or leaves,
avoid them in contact with the exhaust pipe or muffler when parking the vehicle.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for KYMCO X-Town CT125
Summary of Contents for KYMCO X-Town CT125
- Page 1 WARNING To avoid damage from the electronic fuel injection system, do not remove or install the battery when the ignition switch is in the " " position. The long-term storage of the vehicle could cause fuel and engine oil deterioration and probably get into a non-start situation.
- Page 2 Read this Manual carefully This Owner's Manual contains important information on safety, operation and maintenance of KYMCO X-Town CT125/250/300. Anyone who is going to ride should carefully read and understand the contents of this manual before riding. For personal safety, understand and follow all of the warnings contained in this Owner's Manual and the labels attached on vehicle.
- Page 3 R e c o r d t h e Ve h i c l e I d e n t i f i c a t i o n , Engine Serial Number Number , in the blanks above for a reference to assist you in ordering parts from the authorized KYMCO dealer or in case the vehicle is stolen. xxxxx xxxxxxxx...
-
Page 4: Table Of Contents
TABLE OF CONTENTS SECTION 1-SAFETY INTRODUCTION..1 ABS System(Optional)......29 SECTION 4-MAINTENANCE....30 Forward............1 Maintenance Schedule......31 Scooter Safety...........2 Engine Oil..........36 Accessories & Modifications......4 Engine Oil Replacement ......38 Locations of Parts & Controls.......5 Engine Oil Filter Replacement ....39 SECTION 2-CONTROLS & FEATURES..8 Transmission Fluid Change ......42 Air Filter Element Change ......42 Ignition Switch...........8 Throttle Operation........42... -
Page 5: Section 1-Safety Introduction
FORWARD & SAFETY INTRODUCTION Thanks for purchasing this KYMCO X-Town CT125/250/300, and welcome to the KYMCO family. Please read this owner's manual carefully before riding so that you will be thoroughly familiar with the proper operation of controls, features, capabilities, and limitations. -
Page 6: Scooter Safety
SCOOTER SAFETY Keep the vehicle in safe condition IMPORTANT SAFETY INFORMATION For safe riding, it's important to inspect the It will be used longer and pleasure if you take vehicle before every ride and perform all responsibility for your safety and understand recommended maintenance. - Page 7 SCOOTER SAFETY PROTECTIVE CLOTHING The recommended riding gears: ①Wear gloves For your safety, always wear an approved ②Clothes that fit properly motorcycle or scooter helmet, eyes protection, ③Always wear a helmet with eye protection boots, gloves, long pants, and a long-sleeve ④Wear bright or reflective clothing shirt or jacket during a ride.
-
Page 8: Accessories & Modifications
ACCESSORIES & MODIFICATION There is a large variety of accessories available to KYMCO vehicle owners. KYMCO cannot have direct control over the quality or suitability of accessories you may wish to purchase. The addition of unsuitable accessories can lead to unsafe operation. It is not possible for KYMCO to test each accessory on the market or combinations of all the available accessories;... -
Page 9: Locations Of Parts & Controls
LOCATION OF PARTS & CONTROLS Rear Brake Lever Headlight 3 Fuel Filler Cap Helmet Hook Side Stand(with cut off feature) Engine Number 7 Air Cleaner 8 Tail/Brake Light 9 Rear Left Turn Signal Light Luggage Box Seat NOTE: Your scooter may differ slightly in appearance from the images in this manual. - Page 10 LOCATION OF PARTS & CONTROLS Reflector Main Coolant Tank Filler Front Brake Lever Electric Starter Button Ignition Switch Vehicle Identification Number (VIN) Rear Right Turn Signal Light Muffler Oil Filler Cap/dipstickStand Center Stand Flip Foot Peg NOTE: Your scooter may differ slightly in appearance from the images in this manual.
- Page 11 LOCATION OF PARTS & CONTROLS Right Rearview mirror Left Rearview mirror Battery Headlight Front Right Turn Signal Light Front Left Turn Signal Light NOTE: Your scooter may differ slightly in appearance from the images in this manual.
-
Page 12: Section 2-Controls & Features
SECTION 2 -CONTROLS & FEATURES With the ignition key at the “ ” position, IGNITION SWITCH turn it counterclockwise from “ ” to the “ ” To operate the ignition switch and it's functions: position. “ ” Position: All electrical circuits are off. The engine will not “... -
Page 13: Security Shutter
CONTROLS & FEATURES SECURITY SHUTTER To open the ignition switch security shutter : Push the shut button on the ignition switch panel to close the security shutter. To shut the ignition switch security shutter : Insert the specific key until the notch is aligned with the pin Turn clockwise to open the security shutter. -
Page 14: Instruments
CONTROLS & FEATURES High Beam Indicator Light: This light is INSTRUMENTS illuminated when the headlight high beam is Turn Signal Indicator Light: Flashes when either turn signal is being used. Tachometer: Indicates the engine speed in the Speedometer: Indicates the road speed in revolutions per minute (RPM). - Page 15 If it keeps on after starting the engine, it indicates that a fault has been detected in the EFI or elect- -rical system. It needs immediate inspection by the authorized KYMCO dealer. ▆ NOTE: Turn on the ignition switch, The CLEP indicator will always illuminate.
- Page 16 The Oil Pressure Warning Indicator will light up if the oil pressure is lower than normal action when the engine rotates. This denotes a system anomaly; you need to go to a KYMCO dealer for a check-up. Cruise information: Press the “FUNC” button to switch the mode for battery voltage, ambient temperature.
- Page 17 CONTROLS & FEATURES The batter y voltage Display the prompt battery voltage to get the information without need to check battery directly. VOLT The ambient temperature mode Display the surrounding temperature, Press the “FUNC” and “RESET” buttons for 3 seconds to select the unit of “°C” Celsius or “°F”...
- Page 18 CONTROLS & FEATURES 5. Push the MODE button; It will change to Adjust clock make the “minute” digits be flashing. The setting procedure: 1.Turn the ignition switch to the ON position. 2.Push the MODE button for more than 2 seconds to select the ODO mode. 6.Push the RESET button to set the minute.
- Page 19 Even there's an ABS system failure, the system will work normally in conventional braking condition just like a vehicle without ABS system. ▆ NOTE: If the ABS indicates a fault, it's very important to make the authorized KYMCO dealer to check the ABS system immediately.
-
Page 20: Usb Power Supply
CONTROLS & FEATURES USB Power supply This vehicle is equipped with the accessory USB power socket which provides a function to charge the mobile phone with capacity compliance as below. ˙To use the accessory USB power supply, turn on the ignition switch, and then start the engine. ˙Open the cover of the USB socket . -
Page 21: Right-Hand Handlebar Switch
CONTROLS & FEATURES Right handlebar switch Star ter button Press starter button “ ” and pull brake lever in the meantime to actuate the starter motor. ▆ NOTE: The starter motor will not operate unless the side-stand is fully stored up. Engine stop switch Switch button to “... -
Page 22: Left-Hand Handlebar Switch
CONTROLS & FEATURES Left handlebar switch Turn signal switch Push to signal other drivers for an intention to make turn or change lane. The turn signal light is blinking while the switch is pushed left or right. “ ”:for left turn “... -
Page 23: Fuel Recommendation
CONTROLS & FEATURES Fuel level inspection / Refilling Fuel Type and Octane Rating If the low fuel indicator blinks, quickly refill the Use clean, fresh unleaded gasoline with an fuel tank with the specified unleaded gasoline. ethanol volume content not more than 5% Fuel tank filler : and an octane rating equal to or higher than To refuel, do the following:... -
Page 24: Seat
CONTROLS & FEATURES Seat To unlock the seat With the ignition key at the “ ” position (the engine is running), push the key in and turn it counterclockwise from “ ” to the “ ” position. With the ignition key in the “... - Page 25 CONTROLS & FEATURES Components inside the Luggage Box: LED light 1. LED Light of Luggage Box The lamp lights up when Seat Pad is lifted up, goes out when closed. 2. DC12V power socket CAUTION The Luggage Box Light is provided with light-sensing switch;...
- Page 26 CONTROLS & FEATURES Combination Braking System (CBS) Combination Braking System , the rider's action of depressing the rear brake lever applies both front and rear brakes, The amount of each brake applied is determined by CBS pump. Depressing the front brake lever only applies the front brake. ④...
-
Page 27: Suspension
CONTROLS & FEATURES Suspension Each shock absorber on your scooter has 5 spring preload adjustment positions for different load or riding conditions. Use a fitting wrench to turn the adjuster's boss Position 1 is for light loads and smooth road conditions. -
Page 28: Side Stand
Put the side stand up and start the engine. ● Lower the side stand . The engine should ● stop as doing. ▆ NOTE: If the side stand system does not operate as described, see your KYMCO dealer for service. -
Page 29: Section3-Operation
If you 4. Tires: detect any problem, be sure to deal with it, or Check condition and inflation pressure. have the KYMCO dealer to fix it. WARNING 5. Throttle: Check for smooth operation and that it can be Improper maintenance of the motorcycle closed completely in all steering positions. -
Page 30: Break-In
OPERATION Avoid constant low speed Break-in Operate the engine at constant low speed The first 1600km (1000 miles) of riding is very even of light load may cause the running important to the life of usage. Proper break-in part a fit-in problem. Be sure to start up operation during this period will help ensure the engine gently during the break-in maximum life and performance. -
Page 31: Starting The Engine
OPERATION Star ting the engine Always follow the proper starting procedure described here and on the following pages. CAUTION To protect the catalytic converter in the engine's exhaust muffler, avoid idling too long and do not use leaded gasoline. CAUTION To prevent damage to the starter motor, do not operate the starter motor for more than 5 seconds at a time. - Page 32 OPERATION 3. Squeeze the left (rear) brake lever to connect electric power for ready to start engine. 4. Press the starter button with the throttle closed, releases it at once as the engine starts. 5. Keep the throttle closed while warming up the engine.
-
Page 33: Abs System(Optional)
OPERATION ABS SYSTEM (For ABS model) Limitations of ABS The ABS system is the equipment that ABS does not apply the brakes automatically. prevents wheel lockup in case of an It needs to apply the brakes at the right time emergency braking, thus is capable to keep and with the right amount of braking force. -
Page 34: Section 4-Maintenance
It will also help reduce air pollution involved in a crash, be sure to have the and maximize fuel economy. KYMCO dealer inspect all major parts, even if you are able to make some repairs. To properly take care of the motorcycle, the... -
Page 35: Maintenance Schedule
Maintenance should be performed according to the design standards and specifications by the authorized KYMCO dealer. Be serviced by the KYMCO dealer, unless you have the proper tools, service data and are technically qualified. - Page 36 MAINTENANCE(X-TOWN CT125) W HICHEVER FREQUENCY ODOMETER READING (NOTE1) COMES FIRST 20 25 X 1000 km REFER 12 15 X 1000 mi ITEM PAGE MONTH 24 30 AIR CLEANER NOTE 2 SPARK PLUG NOTE 4 THROTTLE OPERATION VALVE CLEARANCE FUEL LINE...
- Page 37 MAINTENANCE(X-TOWN CT125) W HICHEVER FREQUENCY ODOMETER READING (NOTE1) COMES FIRST X 1000 km REFER X 1000 mi ITEM PAGE MONTH CLUTCH SHOE WEAR BRAKE FLUID NOTE 6 BRAKE PAD WEAR BRAKE SYSTEM BRAKE LIGHT SWITCH STEERING BEARINGS HEADLIGHT AIM NUTS,BOLTS,FASTENERS...
- Page 38 MAINTENANCE(X-TOWN CT250/300) W HICHEVER FREQUENCY ODOMETER READING (NOTE1) COMES FIRST X 1000 km REFER X 1000 mi ITEM PAGE MONTH AIR CLEANER NOTE 2 SPARK PLUG NOTE 4 THROTTLE OPERATION VALVE CLEARANCE FUEL LINE CRANKCASE BREATHER NOTE 3 ENGINE OIL ENGINE OIL SCREEN ENGINE IDLE SPEED TRANSMISSION OIL...
- Page 39 MAINTENANCE(X-TOWN CT250/300) W HICHEVER FREQUENCY ODOMETER READING (NOTE1) COMES FIRST X 1000 km REFER X 1000 mi ITEM PAGE MONTH CLUTCH SHOE WEAR BRAKE FLUID NOTE 6 Replace every10000km or every year BRAKE PAD WEAR BRAKE SYSTEM BRAKE LIGHT SWITCH STEERING BEARINGS HEADLIGHT AIM NUTS,BOLTS,FASTENERS...
-
Page 40: Engine Oil
MAINTENANCE Engine oil level inspection Engine oil (X-Town CT125) Check the engine oil level each day before Engine oil recommendation riding. The oil level must be between the Use a high quality 4-stroke engine oil to ensure high line and low line on the oil level longer life. - Page 41 MAINTENANCE Engine oil level inspection Engine oil (X-Town CT250/300) Check the engine oil level each day before Engine oil recommendation riding. The oil level must be between the Use a high quality 4-stroke engine oil to ensure high line and low line on the oil level longer life.
-
Page 42: Engine Oil Replacement
MAINTENANCE Engine oil inspection Engine oil replacement Start engine and keep idling for a few minutes. Engine oil quality is the major factor that affects ● engine life. Change your scooter's engine oil Stop the engine and stand the scooter on level ●... -
Page 43: Engine Oil Filter Replacement
MAINTENANCE Engine oil filter replacement(Only for X- Town CT125) Screw the oil level dipstick off the crankcase. ● Place an oil container beneath the oil filter cap. ● Unscrew the bolts to remove the oil filter cap. ● Take out the O-ring, spring and filter. ●... - Page 44 MAINTENANCE Transmission Gear Oil change(X-Town CT125) 1. Stand the scooter by the center stand. 2. Remove the gear oil drain bolt 3. Remove the gear oil filler bolt ,and then slowly rotate the rear wheel to drain the gear oil off. 4.
- Page 45 MAINTENANCE Transmission Gear Oil change(X-Town CT250/300) 1. Stand the scooter by the center stand. 2. Remove the gear oil drain bolt 3. Remove the gear oil filler bolt ,and then slowly rotate the rear wheel to drain the gear oil off. 4.
-
Page 46: Transmission Fluid Change
MAINTENANCE Air cleaner filter element 0.08~0.24in (2~6mm) The air cleaner filter element should be serviced at regular intervals by the KYMCO dealer. ▆ NOTE: Have the element serviced more often when riding in unusually wet or dusty areas. CAUTION Using the wrong KYMCO air cleaner element... -
Page 47: Spark Plug
After cleaning, check to adjust the spark plug gap to specified limit by using a spark plug gap thickness gauge. The spark plug should be replaced periodically. Recommend to consult with the KYMCO dealer when choosing an alternative spark plug instead. 0.8~0.9 mm Recommended spark plug125:CPR7EA-9... -
Page 48: Brake Fluid Level Inspection
MAINTENANCE Brake fluid Brake fluid level inspection With the scooter in an upright position, check the front and rear fluid level. Change the brake fluid at the time specified in the maintenance schedule. The fluid level should be above the lower level line .If the fluid level is below the lower level mark "L", check over the worn brake pad or leakage. -
Page 49: Brake Level Adjusters
MAINTENANCE Brake lever adjusters There is an adjuster on each brake lever. Each adjuster has 4 positions so that the released lever position can be adjusted to suit the personal grabbing requirement. To adjust the distance of the lever from the handlebar grip, push the lever forward and turn the adjuster to align the number... -
Page 50: Brake Pad Inspection
MAINTENANCE Brake Pad Inspection Inspect the thickness of brake pad to verify if there is enough lining to brake properly. If the wear indicated groove at the brake pad is no longer visible, this means that the brake pad is worn and requires replacement. Before riding, apply braking several times to reach the proper lever stroke and firm feel on braking action that will ensure the brake pads... -
Page 51: Battery
In case troubles contact the KYMCO dealer immediately. Disconnect the negative (-) terminal of contact, administer the following FIRST ●... -
Page 52: Fuse
WARNING Equipped without ABS: Never use a fuse of different rating. ● If the new fuse blows in a short time, ● consult the KYMCO dealer immediately. Equipped with ABS: DO NOT OPEN Good Blown... -
Page 53: Tires
MAINTENANCE Tires WARNING Tire pressure Insufficient tire pressure not only advances Fail to follow the instruction below may wear but also affects the riding stability. Under- result in an accident due to tire failure. The inflated tires make turning not smooth and over- rider's personal safety is dependent on the inflated tires decrease the contact area with the condition of the scooter's tires. - Page 54 An improperly repaired, installed, or balanced tire can cause you to lose control of your scooter or shorten tire life. Ask the authorized KYMCO dealer, or a qualified tire shop to perform tire repair, replacement, and balancing due to the proper tools and experience are required.
-
Page 55: Coolant
MAINTENANCE Coolant Coolant level inspection The coolant reservoir is under the left foot panel. Check the coolant lever through the inspection window at the left side skirt white the engine is at the normal operating temperature, with the scooter in an upright position. If the level is below the “LOW”... - Page 56 ∎ Use a higher concentration of anti-freeze in freezing weather and be replaced by the Coolant recommendation KYMCO dealer. This higher concentration Use the proper type and amount of coolant. of antifreeze should not exceed 60%. When The coolant must be in good condition and...
-
Page 57: Clean The Windshield
MAINTENANCE Crankcase Blow-by Drain Clean the Windshield and The air cleaner has a drain tube that is for Plastic par ts draining the oil condensed fluid from the To avoid possible scratches, use only water crankcase. and a soft cloth or sponge to clean the When the fluid has accumulated to a certain windshield and other plastic parts with a soft amount in the transparent drain tube, remove... -
Page 58: Storage
MAINTENANCE Removal from Storage STORAGE ˙Remove cover from the vehicle Take necessary steps to be in good condition ˙Check the battery voltage or charge it if for next use after long storage. necessary, and then install it in the vehicle. ˙... -
Page 59: Emission Control
EMISSION CONTROL Crankcase Emission Control System The motorcycle is equipped with a closed crankcase system. Blow-by gas is recycled into the combustion chamber via the intake system. This arrangement is to prevent blow-by gas from spreading to the atmosphere. Exhaust Emission Control System The exhaust emission from the motorcycle is controlled by combustion management fuel delivery ignition setting and exhaust system. -
Page 60: Specifications
SPECIFICATIONS X-Town CT125 Dimensions Chassis Overall length.......2200 mm Tire size, front......120/70-13 Overall width........810 mm Tire size, rear......150/70-13 Overall height....1320 /1120/1185mm Brake (front)........CBS Wheel base........1500 mm Brake (rear).........CBS Capacities Electrical Engine oil (Exchange)......1.0 L Ignition type....Inductive ignition coil Transmission oil (Exchange)....0.12 L Battery.........12V10Ah... - Page 61 SPECIFICATIONS X-Town CT250 Dimensions Chassis Overall length.......2200 mm Tire size, front......120/70-13 Overall width........810 mm Tire size, rear......150/70-13 Overall height.......1320 mm Brake (front)........ABS Wheel base........1500 mm Brake (rear).........ABS Capacities Electrical Engine oil (Exchange)......0.9 L Ignition type....Inductive ignition coil Transmission oil (Exchange)....0.18 L Battery.........12V10Ah Fuel tank..........10.5 L Headlight......12V 16W /32W...
- Page 62 SPECIFICATIONS X-Town CT300 Dimensions Chassis Overall length.......2200 mm Tire size, front......120/70-13 Overall width........810 mm Tire size, rear......150/70-13 Overall height.......1320 mm Brake (front)........ABS Wheel base........1500 mm Brake (rear).........ABS Capacities Electrical Engine oil (Exchange)......0.9 L Ignition type....Inductive ignition coil Transmission oil (Exchange)....0.18 L Battery.........12V10Ah Fuel tank..........10.5 L Headlight......12V 16W /32W...
Need help?
Do you have a question about the X-Town CT125 and is the answer not in the manual?
Questions and answers
Necesito manual de taller de Kymco xtown ct 125 2022