Idemia MorphoAccess SIGMA Extreme Series Quick Installation Manual

1
Φ = 4mm
3
Φ = 4mm
5
Φ = 4mm
Scale 1.0
Ø44,00mm
40mm min
82,00mm
Technical Support and Hotline
USA & Canada
Mail: support.bioterminals.us@idemia.com
2
Tel: +1 888 940 7477
LATAM (Latin America)
Φ = 4mm
Mail: support.bioterminals.us@idemia.com
Tel: +1 714 575 2973
EMEA (Europe, Middle-East, Africa)
Mail: support.bioterminals@idemia.com
Tel: +33 1 30 20 30 40
APAC (Asia & Pacific)
Mail: support.bioterminals.in@idemia.com
Tel: +91 8929 159 665
India
Mail: support.bioterminals.in@idemia.com
Tel: +91 1800 120 203 020
Detailed instructions are available at
Des instructions détaillées sont disponibles sur
El detalle de las instrucciones está disponible en
https://biometricdevices.idemia.com
4
COPYRIGHT © 2021, IDEMIA
Φ = 4mm
Head office :
2, place Samuel de Champlain - 92400 Courbevoie
Regulatory, safety and environmental notices
Products bearing the CE marking comply with one or more of the following
EU Directives as may be applicable:

Low Voltage Directive 2006/95/EC.

EMC Directive 2004/108/EC.

R&TTE Directive 1999/5/EC.

Ecodesign Directive 2009/125/EC.

RoHS Directive 2011/65/EU.
Compliance with these directives is assessed using applicable European
Harmonised Standards.
This symbol means Direct Current (DC)
The installation of this product should be made by a qualified service
Person and should comply with all local regulations.
It is strongly recommended to use a class II power supply at 12VDC 1A
minimum or at 24VDC 500mA minimum in conformity with Safety Electrical
Low Voltage (SELV). The power supply cable length should not exceed 10
meters.
This system must be installed in accordance with the National Electrical
Code (NFPA 70), and the local authority having jurisdiction.
This product is intended to be installed with a power supply complying with
IEC60950-1, in accordance with the NEC Class 2 requirements; or supplied
by a listed IEC60950-1 external Power Unit marked Class 2, Limited Power
source, or LPS and rated 12VDC, 1A minimum or 24VDC, 0,5A minimum.
In case of building-to-building connection (power source in a building, and
terminal in another building), it is recommended to connect the 0V of the
power supply to the earthing system of the building. And the terminal block
Power Ground must be connected with the earthing system of the other
building.
Note that all connections of the MorphoAccess® SIGMA Extreme Series
6
terminal described hereafter are of SELV (Safety Electrical Low Voltage)
type.
Φ = 4mm
This symbol means do not dispose of your product with your other
household waste. Instead, you should protect human health and the
environment by handing over your waste equipment to a designated
collection point for the recycling of waste electrical and electronic
equipment.
®
MorphoAccess SIGMA Extreme Series
Quick Installation Guide
Qu ick
Gu id e
WEE E
Optional Wi-Fi™
Status LED Interface (plugged at
the back of the terminal)
Microphone
Camera
Light Sensor
5" WVGA
touchscreen
Biometric
sensor
Speaker
USB host port
RF Card reader
Models:
MorphoAccess® Sigma Extreme iClass (MPH-AC002B)
MorphoAccess® Sigma Extreme Multi (MPH-AC002B)
MorphoAccess® Sigma Extreme Prox (MPH-AC002A)
MorphoAccess® Sigma Extreme iClass FFD (MPH-AC002B)
MorphoAccess® Sigma Extreme Multi FFD (MPH-AC002B)
MorphoAccess® Sigma Extreme Prox FFD (MPH-AC002A)
UL294 Performance levels
Access
Destructive Stand-by
Control Line Endurance Conditions
Attack Power
Security
Level I Level I Level IV Level I NA
LCD