Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Idemia MorphoTop Slim
Summary of Contents for Idemia MorphoTop Slim
- Page 1 MorphoTop Slim Installation guide CETE | Global R&D | November 2017 | V1...
-
Page 2: Table Of Contents
CONTENTS INTRODUCTION ............................... 3 RECOMMENDATIONS ............................. 3 General precautions ............................ 3 Cleaning precautions ........................... 3 Warning ................................. 3 SAFETY INSTRUCTIONS..........................4 Europe information ............................4 Caution ................................4 USA information ............................4 Caution ................................4 GENERAL DESCRIPTION..........................5 RECOMMENDED DEVICE INSTALLATION ....................6 TECHNICAL CHARACTERISTICS ....................... -
Page 3: Introduction
Intuitive and easy-to-use Interface, • Open architecture, with dedicated applications implemented via the Morpho LiveScan Software Development Kit and MorphoBop SDK. To ensure the most effective use of your MorphoTop Slim, we recommend that you read this Installation Guide thoroughly. RECOMMENDATIONS General precautions •... -
Page 4: Safety Instructions
USB3 link of the PC with a nominal voltage of 5V DC (as shown on the product label: 5V ). Europe information Hereby declares that the MorphoTop Slim has been tested and found compliant with the following standards as required by the EMC Directive: 2014/30/EU... -
Page 5: General Description
GENERAL DESCRIPTION Acquisition type indicators Acquisition Status indicators: • Orange means harder pression on related finger is requested Acquisition surface Rolled acquisition area limitation for USB2 2 mounting holes for M3 screw USB trapdoor, to be able to change USB cable if necessary. Tightening torque of associated screws (*4): 0.2 Nm 5/11... -
Page 6: Recommended Device Installation
RECOMMENDED DEVICE INSTALLATION To optimize the ergonomic of Thumb acquisition, it is advised to set up the product a bit over the table (and fixed on the table, thanks to the 2 mounting holes defined just before), as shown below: Drawing to drill the table: 6/11 CETE | Global R&D... - Page 7 Use two M3 screws to maintain the product to the table. Choose a screw length = table thickness + 3 to 5.5mm. Fix them gently without exceeding max force of 0.9 Nm, and with M3 washers (1,1 mm thickness +/-0,1 mm) between the terminal and the support 7/11 CETE | Global R&D November 2017 | V1...
-
Page 8: Technical Characteristics
MorphoTop Slim: Slap Finger Print scanner (4/4/2), at 500 ppi IQS Appendix F certified, with VERIF license MorphoTop Slim R: Rolled Finger Print acquisition added, with ROLLED license Device Option (license containers) : to use activeX MorphoPAK for camera acquisition... -
Page 9: Software Environments
MorphoTOP device It is highly recommended to plug MorphoTop Slim on a USB3 port. USB2 port could be not enough for full efficiency of MorphoTop Slim device. You can plug MorphoTop Slim on one USB2 port if it has high power (0,7 A instead of 500mA for nominal port). - Page 10 Then, you will be able to count USB controller on your computer. It is highly recommended to have at least 2 controllers: 1 for MorphoTop Slim 1 for other devices behind a USB Hub 10/11 CETE | Global R&D November 2017 | V1...
-
Page 11: Support
To access this service from Biometric Terminals Business Unit, please send an email rather than call the hot line. Email: mailto:hotline.biometrics@morpho.com Phone: + 33 1 30 20 30 40 Web site: http://www.biometric-terminals.com/ Produced by IDEMIA Identity & Security France Registered office: Adresse : 11 boulevard Galliéni 92130 Issy-les-Moulineaux FRANCE Support For Products sold by other Business Units, please contact your sales / program interface to have support procedure.
Need help?
Do you have a question about the MorphoTop Slim and is the answer not in the manual?
Questions and answers